Where solid partitions or security glazing separate visitors from detainees at least one of each type of cubicle or counter partition shall comply with 904.6....
Search Results "Counter Depth"
Filters
Commonly Searched Documents
-
231.4.2 Partitions
-
Forward Reach [4.2.5]
Since the forward reach over an obstruction is limited by how far a person using a wheelchair can pull up below it, the depth of reach cannot exceed the amount of usable clear floor space...
-
231.4.2 Partitions
Where solid partitions or security glazing separate visitors from detainees, at least one of each type of cubicle or counter partition shall comply with 904.6....
-
11B-231.4.2 Partitions
Where solid partitions or security glazing separate visitors from detainees at least one of each type of cubicle or counter partition shall comply with Section 11B-904.6....
-
11B-231.4.2 Partitions
Where solid partitions or security glazing separate visitors from detainees at least one of each type of cubicle or counter partition shall comply with Section 11B-904.6....
-
11B-231.4.2 Partitions
Where solid partitions or security glazing separate visitors from detainees at least one of each type of cubicle or counter partition shall comply with Section 11B-904.6....
-
Side Reach [4.2.6]
High and low reaches are based on a depth of reach no greater than 10 inches measured from the available clear floor space....
-
Height: ADA Standard Section 902.3
The tops of dining surfaces and work surfaces shall be 28 inches (710 mm) minimum and 34 inches (865 mm) maximum above the finish floor or ground.
-
11B-902.3 Height
The tops of dining surfaces and work surfaces shall be 28 inches (711 mm) minimum and 34 inches (864 mm) maximum above the finish floor or ground.
-
231.4 Visiting Areas
231.4 Visiting Areas. Visiting areas shall comply with 231.4.
-
F231.4 Visiting Areas
Visiting areas shall comply with F231.4.
-
11B-231.4 Visiting areas
Visiting areas shall comply with 11B-231.4.
-
231.4 Visiting Areas
Visiting areas shall comply with 231.4.
-
1133A.4.1 Exceptions
Exceptions: Stone, cultured stone and tiled countertops may be used without meeting the repositioning requirements. Two 15-inch (381 mm) wide minimum breadboards may...
-
1133A.4, Item 1
1. A minimum linear length of 30 inches (762 mm) of countertop shall be provided for the kitchen sink installation.
-
7.3(3)
(3) Signage identifying accessible check-out aisles shall comply with 4.30.7 and shall be mounted above the check-out aisle in the same location where the check-out number or type of...
-
4.7.2 Slope
Slopes of curb ramps shall comply with 4.8.2. The slope shall be measured as shown in Fig. 11. Transitions from ramps to walks, gutters, or streets shall be flush and free of abrupt...
-
4.7.2 SLOPE
Slopes of curb ramps shall comply with 4.8.2. The slope shall be measured as shown in Fig. 11. Transitions from ramps to walks, gutters, or streets shall be flush and free of abrupt...
-
11B-231.4 Visiting areas
Visiting areas shall comply with 11B-231.4.
-
1133A.4, Item 1
1. A minimum linear length of 30 inches (762 mm) of countertop shall be provided for the kitchen sink installation.
-
11B-231.4 Visiting areas
Visiting areas shall comply with Section 11B-231.4.
-
Kitchens, Kitchenettes, or Wet Bars [9.2.2(7)]
Kitchens, Kitchenettes, or Wet Bars [9.2.2(7)] Clear floor space for either a forward or a side approach is permitted for cabinets, counters, sinks, and appliances....
-
K5
If the operating controls are set back 10 to 24 inches from the front edge of the counter or table are they no higher than 46 inches above the floor?...
-
308.3.2 Obstructed High Reach
floor or ground space allows a parallel approach to an element and the high side reach is over an obstruction, the height of the obstruction shall be 34 inches (865 mm) maximum and the depth...