Unit 12 ¾" W, 6" front to back depth (325 x 150mm); 17" (430mm) min. clearance below mounting surface is required....
Search Results "Door Maneuvering Clearance"
-
Bobrick TrimLineSeries Countertop Mounted Paper Towel Dispenser B-526
-
Boolee Voting Booth
All side panel fabric is 300 x 300 urethane-coated polyester Design Specifications All weights and measures subject to minor variations Height: 60: Depth: 24” Width: 34" Clearance...
-
11B-703.7.2.6.3 Unisex toilet and bathing facilities
The circle symbol shall contrast with the door, either light on a dark background or dark on a light background....
-
11B-703.7.2.6.3 Unisex toilet and bathing facilities
The circle symbol shall contrast with the door, either light on a dark background or dark on a light background....
-
A4.34.6.8 REFRIGERATOR/FREEZERS
Locating refrigerators so that their doors can swing back 180 degrees is more convenient for wheelchair users....
-
68.10(12) Element
., telephone, curb ramp, door, drinking fountain, seating, water closet, or public right-of-way....
-
§ 37.13(b)
(b) The vehicle door height requirements for vehicles over 22 feet identified in §38.25(c) of this title apply to solicitations for vehicles under this part after January 25, 1992....
-
§ 38.63(b) Exception
Between-car barriers are not required where platform screens are provided which close off the platform edge and open only when trains are correctly aligned with the doors....
-
11B-809.7.1 Width
Exception: The clear width shall be permitted to be reduced to 32 inches (813 mm) minimum at doors....
-
11B-608.2.3 Alternate roll-in type shower compartments
FIGURE 11B-608.2.3 ALTERNATE ROLL-IN TYPE SHOWER COMPARTMENT SIZE AND CLEARANCE...
-
Post-Mounted Objects [§307.3]
The 12” limit also applies to the clearance between multiple posts (excluding the sloping portions of handrails)....
-
Handrails [ADA Standards §504.6, §505]
Handrails [ADA Standards §504.6, §505] Specifications in the ADA Standards for handrail surfaces and clearances facilitate a power grip along the handrail length....
-
11B-704.5 TTY shelf
The shelf shall be capable of accommodating a TTY and shall have 6 inches (152 mm) minimum vertical clearance above the area where the TTY is to be placed....
-
11B-1009.4.1 Clear deck space
Where two grab bars are provided, the clear deck space shall be centered on the clearance between the grab bars....
-
§ 38.125(a)(1) General
., lift, ramp or bridge plate) complying with either paragraph (b) or (c) of this section and sufficient clearances to permit a wheelchair or other mobility aid user to reach a seating location...
-
11B-1009.4.1 Clear deck space
Where two grab bars are provided, the clear deck space shall be centered on the clearance between the grab bars....
-
1009.4.1 Clear Deck Space
Where two grab bars are provided, the clear deck space shall be centered on the clearance between the grab bars....
-
Section H: Lifts
(§§410.5, 309.4) H6 Is the clear width of the door opening/gate opening at the end of the lift at least 32"?...
-
106 Definitions
The following definitions have been removed as unnecessary, in most cases due to changes in certain scoping or technical requirements: "accessible route," "area of refuge," "automatic door...
-
General [9.1.1]
Where room numbers are provided, they must be raised and Brailled and located on the wall at the latch-sides of doors for safety and uniformity....
-
1011.4, Item 4
Each exit access door from an interior room or area to a corridor or hallway that is required to comply with Section 1011.1, shall be identified by a tactile exit sign with the words “EXIT...
-
Problem Two (Entrance)
Problem Two: The entrance door threshold is one inch high....
-
1013.4, Item 4
Each exit access door from an interior room or area to a corridor or hallway that is required to comply with Section 1013.1, shall be identified by a tactile exit sign with the words “EXIT...
-
11B-216.4.4 Delayed egress locks
Signs required by Chapter 10, Section 1010.1.9.7, Item 6.4 at doors with delayed egress locks shall comply with Sections 11B-703.1, 11B-703.2, 11B-703.3, and 11B-703.5....
