A clear floor space complying with Section 11B-305 positioned for forward approach shall be provided....
Search Results "Shall"
-
11B-902.4.1 Clear floor or ground space
-
11B-407.3.3 Reopening device
Elevator doors shall be provided with a reopening device complying with Section 11B-407.3.3 that shall stop and reopen a car door and hoistway door automatically if the door becomes obstructed...
-
404.2.4 Maneuvering Clearances
Minimum maneuvering clearances at doors and gates shall comply with 404.2.4....
-
505.3 Continuity
Handrails shall be continuous within the full length of each stair flight or ramp run....
-
810.9 Escalators
Where provided, escalators shall comply with the sections 6.1.3.5.6 and 6.1.3.6.5 of ASME A17.1 (incorporated by reference, see "Referenced Standards" in Chapter 1) and shall have a clear...
-
608.3.3 Alternate Roll-In Type Shower Compartments
In alternate roll-in type shower compartments, grab bars shall be provided on the back wall and the side wall farthest from the compartment entry....
-
810.4 Bus Signs
Bus route identification signs shall comply with 703.5.1 through 703.5.4, and 703.5.7 and 703.5.8....
-
707.7.2 Characters
Characters displayed on the screen shall be in a sans serif font. Characters shall be 3/16 inch (4.8 mm) high minimum based on the uppercase letter "I"....
-
1011.3 Operable Parts
Operable parts shall comply with 309.3 and 309.4. EXCEPTIONS: 1. ...
-
R305.1.4 Size
Detectable warning surfaces shall extend 610 mm (2.0 ft) minimum in the direction of pedestrian travel....
-
704.11.1 Parapet construction
Parapets shall have the same fire-resistance rating as that required for the supporting wall, and on any side adjacent to a roof surface, shall have noncombustible faces for the uppermost...
-
1011.3 Operable Parts
Operable parts shall comply with 309.3 and 309.4. EXCEPTIONS: 1....
-
11B-1009.2.4 Seat
The seat shall be rigid and shall have a back support that is at least 12 inches (305 mm) tall....
-
1132A.4.1 Thresholds
Thresholds at the primary entry and required exit doors shall be no higher than ½ inch (12.7 mm)....
-
11B-1009.2.4 Seat
The seat shall be rigid and shall have a back support that is at least 12 inches (305 mm) tall....
-
11B-703.7.2.6.3 Unisex toilet and bathing facilities
The vertices of the triangle shall be located ¼ inch (6.4 mm) maximum from the edge of the circle....
-
11B-407.2.1.5 Signals
Call buttons shall have visible signals that will activate when each call is registered and will extinguish when each call is answered....
-
505.10 Handrail Extensions
Handrail gripping surfaces shall extend beyond and in the same direction of stair flights and ramp runs in accordance with 505.10. EXCEPTIONS: 1....
-
707.5.2 Receipts
Machine location, date and time of transaction, customer account number, and the machine identifier shall not be required to be audible. 2....
-
11B-407.4.7.2 Keypads
Keypads shall be identified by characters complying with Section 11B-703.5 _|Signs; Visual Characters|_ and shall be centered on the corresponding keypad button....
-
407.2.2.1 Visible and Audible Signals
A visible and audible signal shall be provided at each hoistway entrance to indicate which car is answering a call and the car's direction of travel....
-
11B-707.5.2 Receipts
Machine location, date and time of transaction, customer account number, and the machine identifier shall not be required to be audible. 2. ...
-
604.9.1 Location
The water closet shall be located with a wall or partition to the rear and to one side....
-
11B-703.5.6 Height from finish floor or ground
Visual characters shall be 40 inches (1016 mm) minimum above the finish floor or ground. Exceptions: 1. ...