Because the ramp can be moved to different locations, the system usually does not require a building permit for commercial or residential properties....
Search Results "Supplemental Requirement"
-
Handi-Ramp Galvanized Steel Ramps
-
Bradley Contemporary Series Recess Mounted Soap Dispenser 6437
Requires rough wall opening 8½"W x 4½"H x 4"D. Secure to framing with mounting screws (included) at holes provided. Shim at screw points as required....
-
Willoughby Industries Stainless Steel WODS ADA Outdoor Shower
Meets ADA requirements with one (1) standard shower head, one (1) shower head at ADA height, one (1) foot shower, two (2) grab bars, and three (3) pushbuttons for operating showers....
-
Yale 6400LN Series Grade 1 Cylindrical Locks
ADA: The 6400LN meets accessibility guidelines of the Americans with Disabilities Act and the requirements of the Uniform Federal Accessibility Standards and ANSI 117.1, all requiring ease...
-
Pilot Rock End Accessible Multi-Pedestal Table APT Series 3"x4" Recycled Plastic
Use Model ANC1-4 Anchor Kit (Requires 1 kit per leg). FINISH: Standard finish: hot dip galvanized after fabrication for maximum protection from elements. ...
-
TownSteel ED6700 Narrow Stile Concealed Vertical Panic Device
ALRM on part number Warranty: 10-year limited Code Compliance: UL/ULC: Listed panic and safety for all types of 4'x8' single and 8'x8' double doors ANSI/BHMA: Meets A156.3 Grade 1 requirements...
-
Section 36.303(g)(6) Alternative Technologies
Department should require open movie captioning....
-
11B-404.2.5 Thresholds
[2010 ADA Standards] EXCEPTION: Existing or altered thresholds ¾ inch (19 mm) high maximum that have a beveled edge on each side with a slope not steeper than 1:2 shall not be required...
-
11B-222.2 Coat hooks and shelves
shelves are provided in individual compartments at least one of each type complying with Section 11B-803.5 shall be provided in individual compartments in dressing, fitting, or locker rooms required...
-
Transfer Steps: ADA Standard Section 1009.5.4
Where possible, the height of the transfer step should be minimized to decrease the distance an individual is required to lift up or move down to reach the next step to gain access....
-
BATHROOM
A compartmented bathroom is considered a single unit and is subject to the requirements of Chapters 11A and 11B....
-
Height: ADA Standard Section 1005.2.1
or sections 1012.2 and 1012.3 of the International Building Code (2003 edition) (incorporated by reference, see “Referenced Standards” in Chapter 1) is provided, the guard shall not be required...
-
Clearance: ADA Standard Section 804.2
EXCEPTION: Spaces that do not provide a cooktop or conventional range shall not be required to comply with 804.2. Advisory 804.2 Clearance....
-
11B-809.9.4 Work surfaces
Work surfaces shall be 36 inches (914 mm) maximum above the finish floor with minimum lengths at the following locations as required by this section: Linear length of 30 inches...
-
11B-703.7.2.6.1 Men’s toilet and bathing facilities
Exception: Within secure perimeter of detention and correctional facilities, geometric symbols shall not be required to be ¼ inch (6.4 mm) thick....
-
11B-809.9.1 Clear floor space
For a parallel or forward approach to the sink and to the work surface required by Sections 11B-809.9.3 and 11B-809.9.4....
-
BATHROOM
A compartmented bathroom is considered a single unit and is subject to the requirements of Chapters 11A and 11B....
-
11B-404.2.5 Thresholds
[2010 ADA Standards] EXCEPTION: Existing or altered thresholds ¾ inch (19 mm) high maximum that have a beveled edge on each side with a slope not steeper than 1:2 shall not be required...
-
Assembly Area
For the purposes of these requirements, assembly areas include, but are not limited to, classrooms, lecture halls, courtrooms, public meeting rooms, public hearing rooms, legislative chambers...
-
11B-809.9.1 Clear floor space
For a parallel or forward approach to the sink and to the work surface required by Sections 11B-809.9.3 and 11B-809.9.4....
-
11B-703.7.2.6.1 Men’s toilet and bathing facilities
Exception: Within secure perimeter of detention and correctional facilities, geometric symbols shall not be required to be ¼ inch (6.4 mm) thick....
-
11B-222.2 Coat hooks and shelves
shelves are provided in individual compartments at least one of each type complying with Section 11B-803.5 shall be provided in individual compartments in dressing, fitting, or locker rooms required...
-
11B-809.9.4 Work surfaces
Work surfaces shall be 36 inches (914 mm) maximum above the finish floor with minimum lengths at the following locations as required by this section: Linear length of 30 inches...
-
Rebuilding Together Baltimore - Baltimore, MD
Click here to learn more about our eligibility requirements....
