Allowable stresses shall not be exceeded for materials used when a vertical or horizontal force of 250 pounds (1112 N) is applied at any point on the seat, fastener, mounting device or supporting...
Search Results "Positioning Support"
Filters
Commonly Searched Documents
-
4.4.3 Backrest and Armrest
-
Floor Arrival: ADA Standard Section 407.4.8.1.3
Section 407.4.8.1.3 covers the current ADA Standards for visible floor arrival indicators.
-
Signal Level: ADA Standard Section 407.4.8.2.2
Section 407.4.8.2.2: covers the current ADA Standards for the signal level of audible elevator car indicators.
-
Visible Indicators: ADA Standard Section 407.4.8.1
Section 407.4.8.1 covers the current ADA Standards for visible elevator car position indicators.
-
11B-407.4.8.1 Visible indicators
Visible indicators shall comply with Section 11B-407.4.8.1.
-
11B-407.4.8.2.2 Signal level
The verbal annunciator shall be 10 dB minimum above ambient, but shall not exceed 80 dB, measured at the annunciator.
-
11B-407.4.8.1.3 Floor arrival
As the car passes a floor and when a car stops at a floor served by the elevator, the corresponding character shall illuminate. Exception: Reserved. [2010 ADA Standards]...
-
5.2.2 Transfer Surface Size for Equipment Used by Patients in Seated Position
5.2.2 Transfer Surface Size for Equipment Used by Patients in Seated Position....
-
5.2.1.3 Transfer Surface Size for Stretchers
5.2.1.3 Transfer Surface Size for Stretchers. The transfer surface should be 28 inches wide minimum and 17 inches deep minimum located on both long sides of stretchers.
-
M101.2 Application
Sections M301 through M304 shall be applied to diagnostic equipment, based on the patient positions that the equipment supports, during patient transfer and diagnostic use....
-
M301.1 General (Section-by-Section Analysis)
The MDE NPRM proposed that all diagnostic equipment used by patients in a supine, prone, or side-lying position must comply with the technical requirements of proposed section M301....
-
M301.2.2 Transfer Surface Size
However, many X-Ray system tables and all DXA tables will have part of the imaging equipment support located on one of the long sides and only all transfers are made from the other....
-
Armrests (M302.3.2)
M302.3.2 would require armrests to be provided on diagnostic equipment used by patients in a seated position....
-
F103 Modifications and Waivers
The Architectural Barriers Act authorizes the Administrator of the General Services Administration, the Secretary of the Department of Housing and Urban Development, the Secretary of...
-
Tips for Assisting People Who Have Disabilities that are Not Apparent
Service and Emotional Support Animals Be aware that people who have disabilities that are not apparent may travel with emotional support animals or other service animals....
-
Locker Rooms
Locker Rooms Recommendations: Benches of the required size (24 inches deep and at least 48 inches long) can be integrated with lockers so that back support is provided from a wall....
-
How Can You Overcome These Barriers to Work with Your Providers?
There are many things that a person with a disability can do to improve his or her quality of health care and break down the barriers that compromise care. The following suggestions...
-
5.1 Transfer Surface Height Recommendations
The height provision is the same for MDE used by patients in supine, prone, or side-lying positions (M301) and patients in seated positions (M302)....
-
5.7.1 Lift Compatibility Clearance in Base for Equipment Used by Patient in Supine, Prone, or Side-Lying Position
5.7.1 Lift Compatibility Clearance in Base for Equipment Used by Patient in Supine, Prone, or Side-Lying Position....
-
i. Medical examination and treatment tables and chairs
i. Medical examination and treatment tables and chairs Healthcare providers use examination and treatment tables and chairs for many different types of medical and dental...
-
11B-307.4 Vertical clearance
Vertical clearance shall be 80 inches (2032 mm) high minimum. Guardrails or other barriers shall be provided where the vertical clearance is less than 80 inches (2032 mm) high. The...
-
M301.2.1 Height
The transfer surface is permitted to be positioned outside of the specified height range when not needed to facilitate transfer....