EXCEPTION: Wheelchair spaces located on raised platforms shall be permitted to be 32 inches (815 mm) wide minimum to a height of 4 inches (100 mm) measured from the platform surface....
Search Results "Surface Material"
-
M303.2.2 Width
-
CURB RAMP
A sloping pedestrian way, intended for pedestrian traffic, which provides access between a walk or sidewalk and a surface located above or below an adjacent curb face....
-
R409.7 Cross Section
Handrail gripping surfaces shall have a cross section complying with R409.7.1 or R409.7.2....
-
A3
Yes No Note: Unlike at an accessible parking space, the surface for the access aisle of an accessible passenger drop-off area does not have to be marked or striped....
-
C. Parking Slope
Do the parking spaces and access aisles have surface slopes less than 1:50 (i.e.: when measured as shown on the Tools & Techniques page , is the critical dimension 1/2" or less)?...
-
11B-403.5 Clearances
Walking surfaces shall provide clearances complying with Section 11B-403.5....
-
4.19.2 Height and Clearances
Lavatories shall be mounted with the rim or counter surface no higher than 34 in (865 mm) above the finish floor....
-
Reading and Study Areas [8.2]
Recommendation: Specifications in 4.32, including clear passage for accessible routes, knee clearances and surface height (34 inch maximum) should be considered for movable furnishings as...
-
4.29.5 Detectable Warnings at Hazardous Vehicular Areas
If a walk crosses or adjoins a vehicular way, and the walking surfaces are not separated by curbs, railings, or other elements between the pedestrian areas and vehicular areas, the boundary...
-
3.4.7 Openings
Openings in the clear ground space and turning space surface shall not allow passage of a sphere more than 1/2 inch (13 mm) diameter....
-
11B-403.5 Clearances
Walking surfaces shall provide clearances complying with Section 11B-403.5....
-
11B-809.10.8.7 Mirrors and towel bars
Where mirrors are provided the bottom edge of the reflective surface shall be 40 inches (1016 mm) maximum above the finish floor....
-
11B-403.5 Clearances
Walking surfaces shall provide clearances complying with Section 11B-403.5....
-
403.5 Clearances
Walking surfaces shall provide clearances complying with 403.5....
-
Willoughby Industries HS-1014-96-HC 18" wide Lavatory
The construction shall be all welded, with exposed stainless surfaces polished to a #4 satin finish....
-
Tork Foam Soap Dispenser – with Intuition® Sensor, Stainless Steel
Color: Stainless Tork Image Design Foam Skincare Automatic Dispenser system features a gently brushed stainless steel with fine lines; and subtle curves provide clean lines and smooth surfaces...
-
Pilot Rock Bollard Post Barricade
Model TB/P-2 offers bolt down surface installation with welded on 3/8” thick x 10” sq. steel base plate. ...
-
Tork Image Design™ Matic® Hand Towel Roll Dispenser with Intuition® Sensor, Recessed
Image Design™ Matic® Hand Towel Roll Dispenser with Intuition® Sensor Recessed features a gently brushed stainless steel with fine lines; and subtle curves provide clean lines and smooth surfaces...
-
Handbook of Construction Tolerances by David Kent Ballast FAIA, CSI
What is required to successfully detail finish materials on masonry?...
-
Bradley Grab Bars 1 1/2" with Concealed Mounting 812
1½" O.D. heavy duty stainless steel grab bar with concealed mounting: Product Materials FLANGES: 3 1/8" dia. 13 gauge stainless steel. ESCUTCHEONS: 22 gauge stainless steel....
-
AJW Architectural Products UG120-U Series UG120-U 29" Swing-Up, 1.25" Diameter Grab Bar - Configuration U
Gripping Surface: Standard surface is satin finish. Use suffix X for peened grip....
-
Pilot Rock CN-R/D Trash Receptacle
The cross braces have holes for surface mounting options. (Anchor bolts not included). All welded construction - no assembly required....
-
SafetyStepTD Ramp-Up Detectable Warning System
It is surface applied, but when complete it will give the look of a cast in place tile on your street corner....
-
11B-1009.5.7 Grab bars
Where a grab bar is provided on each step, the tops of gripping surfaces shall be 4 inches (102 mm) minimum and 6 inches (152 mm) maximum above each step and transfer platform....
