4550 Back set 5" Material Brass Size 2-3/4" x 4-1/2" Shelf pack 1 Features UL Listed, Works with 1-3/4" doors...
Search Results "Door Surface"
-
Don-Jo Mfg., Inc. 5" Hospital Latch 4550
-
M305.2.1 Location (Section-by-Section Analysis)
surface depths of greater than 24 inches....
-
Don-Jo Mfg., Inc. 2-3/4" Hospital Latch 4500
4500 Back set 2-3/4" Material Brass Size 2-3/4" x 4-1/2" Shelf pack 1 Features UL Listed, Works with 1-3/4" doors...
-
5.4.5 Transfer Support Position for Equipment Used in a Supine, Prone, Side-Lying, or Seated Position
The transfer gripping surface should be located within the minimum and maximum heights....
-
d. Unobstructed Transfer
The MDE NPRM proposed that each transfer side provide unobstructed access to the transfer surface, with an exception to permit temporary obstructions as long as they could be repositioned...
-
Maddak Doorknob Extender
Works as well as more expensive doorknob levers and is easier to install For left or right hand use 5" (12.7 cm) extension handle converts a doorknob into a door lever providing...
-
11B-224.7 Housing at a place of education
and clustered sleeping rooms) or on floors containing accessible sleeping rooms with mobility features shall provide turning spaces that comply with Section 11B-809.2.2 and kitchen work surfaces...
-
Sloped Surfaces
Measuring the slope of a ramp, parking space, pedestrian route, or other ground or floor surface is important to identify whether the surface is accessible....
-
5.4.1 Transfer Support Location for Equipment Used in a Supine, Prone, Side-Lying, or Seated Position
Transfer supports should be required on both sides of the transfer surface and be movable or removable so they can be out of the way during transfer....
-
A Wheelchair Rider's Guide to the California Coast
Explore, enjoy, protect. Rolling across the sand in a beach wheelchair Fishing from an accessible pier Hiking an accessible trail or...
-
5.3.1 Permitted Obstructions to Transfer Sides for M301 and M302
provide options to transfer onto the short side and the long side of the surface....
-
5.4.2 Transfer Support Length for Equipment Used in a Supine, Prone, Side-Lying, or Seated Position
The transfer support should be a minimum length of 15 inches positioned so that the transfer support overlaps the minimum depth of the transfer surface by 80%....
-
1009.4.4 Surface
Surfaces of transfer walls shall not be sharp and shall have rounded edges....
-
1009.5.5 Surface
The surface of the transfer system shall not be sharp and shall have rounded edges....
-
1009.4.4 Surface
Surfaces of transfer walls shall not be sharp and shall have rounded edges....
-
1009.5.5 Surface
The surface of the transfer system shall not be sharp and shall have rounded edges....
-
Sargent HP Bored Lock with Push/Pull Trim
The paddle shape and location create a comfortable target for door activation without using hands....
-
Door and Signal Timing
Section 407.3.4 specifies door and signal timing....
-
Handrails [§504.6, §505]
Handrails [§504.6, §505] Handrails are required on both sides of stairs and must be continuous within the full length of each stair flight. Inside handrails on switchback or...
-
4.2 Physical Accessibility Barriers and Solutions
of the existing counter Facility has two floors but no elevator Ask staff to move equipment that you use to the ground level Install an elevator Interior doors...
-
5.4.3 Transfer Support Height for M301 and M302
5.4.3 Transfer Support Height for M301 and M302 Description: Transfer support height applies to the vertical distance that the gripping area of the support is above the transfer surface...
-
Designing Sidewalks and Trails for Access, Part II of II: Best Practices Design Guide
Source: U.S. Department of Transportation / Beneficial Designs, Inc. Document: 484 pages (9.30 MB PDF) Publication Date: September 2001 This guidebook is the second part of...
