length of the gangway or series of gangways serving as part of a required accessible route is 30 feet (9144 mm) minimum, gangways shall not be required to comply with Section 11B-405.2 _|Slope...
Search Results "Surface Slope"
-
11B-1003.2.2 Boarding piers at boat launch ramps
-
307.3 Post-Mounted Objects
EXCEPTION: The sloping portions of handrails serving stairs and ramps shall not be required to comply with 307.3. Figure 307.3 Post-Mounted Protruding Objects...
-
Q8: Curb Ramp Replaced as Part of a Resurfacing Alteration and Adjacent Sidewalk
Public entities are required to address other barriers on existing sidewalks, such as steep cross slopes or obstructions, as part of their on-going program access and transition plan obligations...
-
406.7 Islands
Each 48 inch (1220 mm) minimum by 36 inch (915 mm) minimum area shall be oriented so that the 48 inch (1220 mm) minimum length is in the direction of the running slope of the curb ramp it...
-
Access to Performing Areas [4.33.5]
Aisles with slopes no steeper than 1:12 are often feasible in small and medium size assembly areas and permit accessible routes that coincide with general routes....
-
Vertical Clearance [§307.4]
Fixed barriers, such as guardrails, are required where the vertical clearance is less than 80” such as at open stairways and along sloped or curved walls....
-
Diagonal Curb Ramps [§406.6]
The orientation also can mislead people with vision impairments who use curb slopes as a cue to crossings....
-
11B-1003.2.2 Boarding piers at boat launch ramps
length of the gangway or series of gangways serving as part of a required accessible route is 30 feet (9144 mm) minimum, gangways shall not be required to comply with Section 11B-405.2 _|Slope...
-
M305.3 Standing Supports (Section-by-Section Analysis)
The Access Board sought public input in questions 39 and 40 in the MDE NPRM preamble on whether the cross section dimensions for gripping surfaces should be applied to standing supports...
-
Bonded Beach Path Installation
The two binder systems used to fabricate the beach path surface were an acrylic and polyvinyl acetate polymer emulsion, SoilSement (Midwest Industrial, Canton, Ohio), mixed 30%...
-
M301.4.2 Clearance Around Base (Section-by-Section Analysis)
The proposed rule required a minimum clearance of 6 inches high measured from the floor and 36 inches deep measured from the edge of the examination surface. NPRM, 77 FR at 6927....
-
Introduction
Four static body dimensions considered relevant to the width and depth dimensions of a seating surface were computed and analyzed to serve as a reference....
-
Appendix B: Overview of Federal Regulations and Guidance for Detectable Warnings
The ADA Accessibility Guidelines for Buildings and Facilities (ADAAG) defines detectable warnings as “a standardized surface feature built in or applied to walking surfaces or other elements...
-
Entrances
Entrances Problem The entrance area must be level (no level change greater than ½ inch) and should not slope steeply in any one direction....
-
1133A.7.1 Plumbing protection
There shall be no sharp or abrasive surfaces under kitchen sinks....
-
405.9.2 Curb or Barrier
curb or barrier shall be provided that prevents the passage of a 4 inch (100 mm) diameter sphere, where any portion of the sphere is within 4 inches (100 mm) of the finish floor or ground surface...
-
TRANSIT BOARDING PLATFORM
[DSA-AC] A horizontal, generally level surface, whether raised above, recessed below or level with a transit rail, from which persons embark/disembark a fixed rail vehicle....
-
405.9.2 Curb or Barrier
curb or barrier shall be provided that prevents the passage of a 4 inch (100 mm) diameter sphere, where any portion of the sphere is within 4 inches (100 mm) of the finish floor or ground surface...
-
1133A.2, Item 3
A clear floor space at least 30 inches (762 mm) by 48 inches (1219 mm) that allows either a parallel or a forward approach shall be provided at the work surface required by Section 1133A...
-
1002.5.2 Transfer Height
The height of amusement ride seats designed for transfer shall be 14 inches (355 mm) minimum and 24 inches (610 mm) maximum measured from the surface of the load and unload area....
-
Note
As shown, there are several ways for grab bars to be designed with adequate gripping surfaces, while ensuring that nothing can be tied onto them....
-
Grab Bar Height
The Board has clarified that the height of grab bars is measured to the top of the gripping surface (609.4)....
-
Mirrors
Provide a mirror in the Spy City Café men's and women's toilet rooms where the bottom edge of the reflecting surface of the mirror is mounted no more than 40" above the finished floor....
-
R305.2.7 Boarding and Alighting Areas
At boarding and alighting areas at sidewalk or street level transit stops for rail vehicles, detectable warning surfaces shall be placed at the side of the boarding and alighting area facing...