For general understanding, site-specific information such as grading, slopes and cross-slopes are not included in a prototype design and thus, the design concept for all exterior elements...
Search Results "Surface Slope"
-
Accessible Route to Dumpster and Enclosure
-
Appendix C Rotational Penetrometer Data Form
Appendix C National Center on Accessibility - National Trails Surface Study Rotational Penetrometer Data Form Trails Information Trail Name: ...
-
6. Dissemination Activities
Development of Surface Roughness Standards for Pathways used by Wheelchairs. Presented at Transportation Research Board Annual Meeting. Washington D.C....
-
T503.4 Steps at Other Doorways
The walking surface on steps serving all other non-rail vehicle doorways shall be lighted at all times with 2 foot-candles (22 lux) minimum of illumination....
-
903.5 Height
The top of the bench seat surface shall be 17 inches (430 mm) minimum and 19 inches (485 mm) maximum above the finish floor or ground....
-
5.3.3.1 Height
The total height of the toilet seat on the riser for a pit toilet shall be between 17 inches (430 mm) and 19 inches (485 mm) above the floor or ground surface....
-
4.34.6.5(8)
(8) There shall be no sharp or abrasive surfaces under sinks. Hot water and drain pipes under sinks shall be insulated or otherwise covered. Figure 51 Kitchen Sink...
-
5.3.3.1 Height
The total height of the toilet seat on the riser for a pit toilet shall be between 17 inches (430 mm) and 19 inches (485 mm) above the floor or ground surface....
-
Garage Parking
At sites that also include surface lots, a garage is treated as a separate parking facility for scoping purposes....
-
1133A.7.1 Plumbing protection
There shall be no sharp or abrasive surfaces under kitchen sinks....
-
1133A.7.1 Plumbing protection
There shall be no sharp or abrasive surfaces under kitchen sinks....
-
Alterations
Section 226.1, exempts sales and service counters from the technical requirements of 902 (dining surfaces and work surfaces)....
-
Public Rights-of-Way: ADA Standard Section 1.
issues, including access for blind pedestrians at street crossings, wheelchair access to on-street parking, and various constraints posed by space limitations, roadway design practices, slope...
-
406.7 Islands
Each 48 inch (1220 mm) minimum by 36 inch (915 mm) minimum area shall be oriented so that the 48 inch (1220 mm) minimum length is in the direction of the running slope of the curb ramp it...
-
307.3 Post-Mounted Objects
EXCEPTION: The sloping portions of handrails serving stairs and ramps shall not be required to comply with 307.3. Figure 307.3 Post-Mounted Protruding Objects...
-
Shooting Facilities
Fixed firing positions must have a 60-inch diameter space with slopes not steeper than 1:48 so a wheelchair user can turn around and have a level place from which to shoot....
-
Clear Deck Space
The slope of the clear deck space must not be greater than 1:48 (2%)....
-
1007.1 Accessible means of egress required
In assembly spaces with sloped floors, one accessible means of egress is required from a space where the common path of travel of the accessible route for access to the wheelchair spaces...
-
Temporary Solutions for Election Day
Suggestion: Install a portable ramp no steeper than 1:12 slope with edge protection and handrails...
-
11B-106.5 Defined terms
POOL CCR CHARACTERS CHILDREN’S USE CIRCULATION PATH CLEAR CLEAR FLOOR SPACE CLOSED-CIRCUIT TELEPHONE COMMERCIAL FACILITIES COMMON USE COMPLY WITH CROSS SLOPE...
-
11B-206.2.1 Site arrival points
(1) Newly constructed or altered streets, roads, and highways must contain curb ramps or other sloped areas at any intersection having curbs or other barriers to entry from a street...
-
Behavioral Safety Products #DH410 Cylindrical Ligature Resistant Lever Handle
The escutcheon plate is sloped at a low profile, from the door to the lever handle itself, to eliminate any further ligature points, and maintains extremely tight tolerances. ...
-
Salsbury Industries 62000 Series Double Tier 3 Wide Standard Metal Lockers
combination or key locks and combination or key padlocks Salsbury Industries is an ISO 9001: 2008 certified company and has excelled in the field of manufacturing since 1936 Options Sloping...
-
Salsbury Industries 63000 Series Triple Tier 3 Wide Standard Metal Lockers
combination or key locks and combination or key padlocks Salsbury Industries is an ISO 9001: 2008 certified company and has excelled in the field of manufacturing since 1936 Options Sloping...
