Except as provided in Sections 11B-403.5.2 and 11B-403.5.3, the clear width of walking surfaces shall be 36 inches (914 mm) minimum....
Search Results "Kitchen Work Surface"
-
11B-403.5.1 Clear width
-
801.1 Scope
For example, 806 addresses guest rooms in transient lodging facilities while 902 contains the technical specifications for dining surfaces....
-
M301.4.2 Clearance Around Base
The base of the equipment shall provide a clearance 6 inches (150 mm) high minimum measured from the floor and 36 inches (915 mm) deep minimum measured from the edge of the examination surface...
-
903.4 Back Support
Back support shall be 42 inches (1065 mm) long minimum and shall extend from a point 2 inches (51 mm) maximum above the seat surface to a point 18 inches (455 mm) minimum above the seat...
-
M302.4.2 Clearance Around Base
The base of the equipment shall provide a clearance 6 inches (150 mm) high minimum measured from the floor and 36 inches (915 mm) deep minimum measured from the edge of the examination surface...
-
801.1 Scope
For example, 806 addresses guest rooms in transient lodging facilities while 902 contains the technical specifications for dining surfaces....
-
382.71 What other aircraft accessibility requirements apply to carriers?
This provision, like its counterpart in the existing rule, requires maintenance of accessibility features in proper working order and tells carriers to ensure that any replacement or refurbishing...
-
Reasonable Accommodations
A reasonable accommodation is any modification or adjustment to a job, the job application process, or the work environment that will enable a qualified applicant or employee with a disability...
-
Standard Forest Service National Trail Specifications
The engineering management publication "Standard Specifications for Construction and Maintenance of Trails" (EM–7720–103) provides a uniform set of specifications for contracted trail work...
-
9.6 ATTENDANCE-RECORDING EQUIPMENT
Time clocks, card racks, log books, and other work assignment or attendance-recording equipment used by people in wheelchairs must be installed at a height no more than 48 in (1220 mm) above...
-
3. How can state and local governments’ employment service systems ensure that people with disabilities have access to competitive integrated employment?
A: Over the past three decades, integrated supported employment services have emerged as a leading model for enabling persons with disabilities to work in competitive integrated employment...
-
Transition Plate
A sloping pedestrian walking surface located at the end(s) of a gangway....
-
T303.3 Cross Section
Gripping surfaces shall have a cross section complying with T303.3....
-
M302.3 Supports
Transfer supports, armrests, and reclining surfaces shall comply with M302.3....
-
M301.3 Supports
Transfer supports, stirrups, and reclining surfaces shall comply with M301.3....
-
106.5.72 Transition Plate
A sloping pedestrian walking surface located at the end(s) of a gangway....
-
Inclusion Solutions Sensitivity to Voters With Disabilities DVD
Highly rated training video educates poll works on access....
-
Integralift Fixed Ceiling Lift
Integralift Fixed ceiling lifts can be safer and easier to use than mobile lifts, and can work in smaller rooms where mobile lifts can be hard to maneuver....
-
Accessible
., usable doors, an accessible route, accessible environmental controls, and usable kitchens and bathrooms) and the "adaptable" structural feature of reinforced bathroom walls for later...
-
Design Guidelines for the Hearing and Visually-Impaired
switches, electrical outlets, thermostats, and other environmental controls in accessible locations; reinforcements in bathroom walls to allow later installation of grab bars; and usable kitchens...
-
11B-801.1 Scope
For example, 806 addresses guest rooms in transient lodging facilities while 902 contains the technical specifications for dining surfaces....
-
703.4.1 Height above Finish Floor or Ground
Tactile characters on signs shall be located 48 inches (1220 mm) minimum above the finish floor or ground surface, measured from the baseline of the lowest tactile character and 60 inches...
-
M302.4.2 Clearance Around Base
the diagnostic equipment shall provide a clearance 6 inches (150 mm) high minimum measured from the floor and 36 inches (915 mm) deep minimum measured from the edge of the examination surface...
-
M301.4.2 Clearance Around Base
base of diagnostic equipment shall provide a clearance 6 inches (150 mm) high minimum measured from the floor and 36 inches (915 mm) deep minimum measured from the edge of the examination surface...
