Floor designations shall be provided in both raised characters and braille. Raised characters shall be 2 inches (51 mm) high....
Search Results "Raised Crossing"
Filters
Commonly Searched Documents
-
11B-407.2.3.1 Floor designation
-
11B-407.2.3.1 Floor designation
Floor designations shall be provided in both raised characters and Braille. Raised characters shall be 2 inches (51 mm) high....
-
1.1.14 Flatness of ramp cross slope
1.1.14 Flatness of ramp cross slope....
-
11B-407.2.3.1 Floor designation
Floor designations shall be provided in both raised characters and braille. Raised characters shall be 2 inches (51 mm) high....
-
Elevated Dune Crossings
An dune crossing that is elevated or has a slope that exceeds 1:20 (5 percent) that is part of a beach access route must have handrails and edge protection (figure 118)....
-
4. Example: Installing Curb Ramps for Program Accessibility
Under these requirements, the town may choose to install curb ramps at all pedestrian crossings on the sidewalks surrounding the town hall, but it is not necessarily required to do so....
-
11B-407.4.9 Emergency communication
Raised symbols or characters, white on a black background, and Braille shall be provided adjacent to the device and shall comply with Sections 11B-703.2 and 11B-703.3....
-
11B-407.4.9 Emergency communication
Raised symbols or characters, white on a black background, and Braille shall be provided adjacent to the device and shall comply with Sections 11B-703.2 and 11B-703.3....
-
11B-407.4.9 Emergency communication
Raised symbols or characters, white on a black background, and Braille shall be provided adjacent to the device and shall comply with Sections 11B-703.2 and 11B-703.3....
-
Allowances for Typical Roadway Geometry
The draft guidelines also permitted the cross slope of pedestrian access routes within midblock pedestrian street crossings and of curb ramps at midblock pedestrian street crossings to equal...
-
12 [§ 4.7.9]
12 [§ 4.7.9] When a curb ramp is located at a marked crossing, the area where the ramp run ends must be contained within the marked crossing....
-
Colorado Cross-Disability Coalition, et al. Plaintiffs, v. Abercrombie & Fitch Co., et al., Defendants. - Statement of Interest on the Parties' Motions for Summary Judgment
IN THE UNITED STATES DISTRICT COURT FOR THE DISTRICT OF COLORADO Civil Action No. 09-cv-02757-WYD-KMT COLORADO CROSS-DISABILITY COALITION, et al. ...
-
1. Location
Generally, you must provide curb ramps wherever a sidewalk or other pedestrian walkway crosses a curb. ...
-
1.1.4 Walk cross slope
1.1.4 Walk cross slope....
-
Cross Section of Gripping Surfaces
specify the following dimensions for grab bars to enable individuals with disabilities to firmly grasp the grab bars and support themselves during transfers: • Grab bars with circular cross...
-
1.1.2 Walks
Measure walks and other non - ramp pedestrian surfaces for overall running slope and cross slope as well as local running slope and cross slope variations (flatness) in accordance with 1.1.3...
-
11B-406.5.1 Location
Curb ramps at marked crossings shall be wholly contained within the markings, excluding any flared sides. Exception: Diagonal curb ramps shall comply with Section 11B-406.5.9....
-
M305.2.4.1 Circular Cross Section
Transfer supports with circular cross sections shall have an outside diameter of 1 ¼ inches (32 mm) minimum and 2 inches (51 mm) maximum....
-
Trail Slopes
Cross slopes that are too steep can be difficult to traverse, but trails with too little cross slope tend to become streams. Water running down or ponding on trails destroys them....
-
1017.7 Slopes
This section contains technical requirements for the maximum running slope and segment length (1017.7.1) and cross slope (1017.7.2) of trails....
-
407.4.7.2 Keypads
The number five key shall have a single raised dot. The dot shall be 0.118 inch (3 mm) to 0.120 inch (3.05 mm) base diameter and in other aspects comply with Table 703.3.1....
-
407.4.7.2 Keypads
The number five key shall have a single raised dot. The dot shall be 0.118 inch (3 mm) to 0.120 inch (3.05 mm) base diameter and in other aspects comply with Table 703.3.1....
-
407.4.7.2 Keypads
The number five key shall have a single raised dot. The dot shall be 0.118 inch (3 mm) to 0.120 inch (3.05 mm) base diameter and in other aspects comply with Table 703.3.1....
-
403.3 Slope
The cross slope of walking surfaces shall not be steeper than 1:48....