Corada

1008.2.5.3.1 Handrail Gripping Surfaces

Handrail gripping surfaces with a circular cross section shall have an outside diameter of 0.95 inch (24 mm) minimum and 1.55 inches (39 mm) maximum....

1008.2.5.3.1 Handrail Gripping Surfaces

Handrail gripping surfaces with a circular cross section shall have an outside diameter of 0.95 inch (24 mm) minimum and 1.55 inches (39 mm) maximum....

11B-1008.2.5.3.1 Handrail gripping surfaces

Handrail gripping surfaces with a circular cross section shall have an outside diameter of 0.95 inch (24 mm) minimum and 1.55 inches (39 mm) maximum....

11B-1008.2.5.3.1 Handrail gripping surfaces

Handrail gripping surfaces with a circular cross section shall have an outside diameter of 0.95 inch (24 mm) minimum and 1.55 inches (39 mm) maximum....

505.7.1 Circular Cross Section

505.7.1 Circular Cross Section. Handrail gripping surfaces with a circular cross section shall have an outside diameter of 1¼ inches (32 mm) minimum and 2 inches (51 mm) maximum....

Non-Circular Cross Section and Clearance (§505.5, §505.7)

Non-Circular Cross Section and Clearance (§505.5, §505.7)...

1008.2.5.3.1 Handrail Gripping Surfaces

Handrail gripping surfaces with a circular cross section shall have an outside diameter of 0.95 inch (24 mm) minimum and 1.55 inches (39 mm) maximum....

7.4.5.2 Slope

The cross slope of a passing space shall not exceed 1:20 (5 percent) in any direction....

Can platform lifts be portable or provided after construction as an adaptation?

Platform lifts can be provided after construction only to provide access to raised work stations in courtrooms (sufficient space and electrical service must be provided in design to facilitate...

4.8.6 Cross Slope and Surfaces

The cross slope of ramp surfaces shall be no greater than 1:50. Ramp surfaces shall comply with 4.5....

4.8.6 CROSS SLOPE AND SURFACES

The cross slope of ramp surfaces shall be no greater than 1:50. Ramp surfaces shall comply with 4.5....

Handrail Clearance and Cross Section [§505.5, §505.7]

Handrail Clearance and Cross Section [§505.5, §505.7] Surface requirements and clearances facilitate a power grip along the length of handrails....

505.7.1 Circular Cross Section

Handrail gripping surfaces with a circular cross section shall have an outside diameter of 1¼ inches (32 mm) minimum and 2 inches (51 mm) maximum....

Figure 609.2.2 Grab Bar Non-Circular Cross Section – Drawing from the U.S. Access Board

505.7.1 Circular Cross Section

Handrail gripping surfaces with a circular cross section shall have an outside diameter of 1 1/4 inches (32 mm) minimum and 2 inches (51 mm) maximum....

505.7.1 Circular Cross Section

Handrail gripping surfaces with a circular cross section shall have an outside diameter of 1 1/4 inches (32 mm) minimum and 2 inches (51 mm) maximum....

703.2.8 Line Spacing

Spacing between the baselines of separate lines of raised characters within a message shall be 135 percent minimum and 170 percent maximum of the raised character height....

Location: ADA Standard Section 407.4.7.1.2

Section 407.4.7.1.2 covers the current ADA Standards for the location of designations and indicators on elevator car control buttons.

3 [§ 4.3.7]

3 [§ 4.3.7] The cross slope of the curb ramp is perpendicular to the running slope. Unlike the running slope, which runs along the ramp, the cross slope is measured across the ramp....

11B-707.6.1 Input controls