R308.1.1.1 Dimensions....
Search Results "Maximum Dimension"
-
R308.1.1.1 Dimensions
-
§ 35.151(b) Alteration
(b) Alteration.
-
§ 35.151(b) Alterations.
(b) Alterations.
-
§ 37.43 Alteration of transportation facilities by public entities
[See subsections ...]
-
11B-202.3 Alterations
In alterations, where compliance with applicable requirements is technically infeasible, the alteration shall comply with the requirements to the maximum extent feasible....
-
810.2.2 Dimensions
Figure 810.2.2 Dimensions of Bus Boarding and Alighting Areas...
-
703.3.1 Dimensions and Capitalization
Table 703.3.1 Braille Dimensions Measurement Range Minimum in Inches Maximum in Inches Dot base diameter 0.059...
-
Maximum Force
The Board sought comment on whether the maximum 5 pounds of force was appropriate for operating controls activated by a single finger, such as elevator call and control panel buttons, platform...
-
F202.4 Alterations Affecting Primary Function Areas
to the requirements of F202.3, an alteration that affects or could affect the usability of or access to an area containing a primary function shall be made so as to ensure that, to the maximum...
-
11B-202.3 Alterations
Any elements or spaces of the building or facility that are required to comply with these requirements must be made accessible within the scope of the alteration, to the maximum extent feasible...
-
703.3.1 Dimensions and Capitalization
Table 703.3.1 Braille Dimensions Measurement Range Minimum in Inches Maximum in Inches Dot base diameter 0.059 (1.5 mm) to 0.063 (1.6 mm)...
-
Alterations
If compliance is technically infeasible, the alteration must comply to the maximum extent feasible....
-
11B-703.3.1 Dimensions and capitalization
11B-703.3.1 Dimensions and capitalization. Braille dots shall have a domed or rounded shape and shall comply with Table 11B-703.3.1....
-
703.3.1 Dimensions and Capitalization
Table 703.3.1 Braille Dimensions Measurement Range Minimum in Inches Maximum in Inches Dot base diameter 0.059 (1.5 mm) to 0.063 (1.6 mm)...
-
Section 35.151(b) Alterations (Section-by-Section Analysis)
of public accommodation or commercial facility that affects or could affect the usability of or access to an area that contains a primary function, the entity shall ensure that, to the maximum...
-
205 and 309 Operable Parts
205 and 309 Operable Parts Section 4.1.3, and more specifically sections 4.1.3(13), 4.27.3, and 4.27.4 of the 1991 Standards, require operable parts on accessible elements, along...
-
4.1.6(3)(f)(i)
(i) Where it is technically infeasible to disperse accessible seating throughout an altered assembly area, accessible seating areas may be clustered. Each accessible seating area...
-
4.1.6(4)(f)
(f) Assembly areas. (i) In alterations where it is structurally impracticable to disperse seating throughout the assembly area, seating may be located in collected areas as...
-
Alterations to Qualified Historic Facilities [§202.5]
Alterations to qualified historic facilities must comply with section 202.5 to the maximum extent feasible....
-
11B-408.4.1 Car dimensions and doors
ETA Editor's Note Lacking Exception 2 above allowed by 2010 ADA Standards, the CBC requirements pertaining to car dimensions at existing limited-use/limited-application elevators are...
-
11B-408.4.1 Car dimensions and doors
ETA Editor's Note Lacking Exception 2 above allowed by 2010 ADA Standards, the CBC requirements pertaining to car dimensions at existing limited-use/limited-application elevators are...
-
Section 36.403 Alterations: Path of Travel (Section-By-Section Analysis and Response to Comments)
requirement that any alteration that affects or could affect the usability of or access to an area of a facility that contains a primary function shall be made so as to ensure that, to the maximum...
-
LULA Elevator Dimensions
In the final rule, the Board has added alternate dimensions which are substantively consistent with the latest edition of the ANSI A117.1 standard....
-
4. ABSOLUTE DIMENSIONS
ABSOLUTE DIMENSIONS: In the few cases where absolute dimensions are indicated, the application of construction tolerances is most likely to be influenced....