Thigh breadth for this analysis was computed as the larger of two dimensions, the horizontal distance between the lateral (outer) aspect of the hips, and the horizontal distance between...
Search Results "Dimension"
Filters
Commonly Searched Documents
-
1. Thigh Breadth
-
M302.2.3 Size (Section-by-Section Analysis)
increased to 17 inches, a disability advocate recommended increasing the width to 23 inches, two of the commenters, accessibility consultant and disability advocate, stated that the proposed dimensions...
-
5.8.2.5 Toe Height Recommendation
A toe space dimension usually defines a static unobstructed space. However, in the case of mammography, as the breast platform moves up and down, the toe space changes....
-
608.2.1 Transfer Type Shower Compartments
Transfer type shower compartments shall be 36 inches (915 mm) by 36 inches (915 mm) clear inside dimensions measured at the center points of opposing sides and shall have a 36 inch (915...
-
Bike Lane Width
The AASHTO Guide for the Development of Bicycle Facilities (p. 22) recommends a minimum width for bike lanes of 1.2 m (4 ft).(2) While this dimension appears to be adequate to accommodate...
-
Bus Stop Pads
The proposed rule specified that these dimensions were required to "the maximum extent allowed by legal or site constraints" (1002.2.2)....
-
Technical Requirements for Accessible Hiker/Pedestrian Trails
Wheelchair dimensions, clear space, maneuvering room, and reach ranges found in Architectural Barriers Act Accessibility Standards (ABAAS) are the basis for trail designs that maximize accessibility...
-
5.2.2.2 Transfer Surface Depth Recommendation for M302
The Committee easily supported this increase as existing equipment already meets or exceeds this dimension....
-
608.2.3 Alternate Roll-In Type Shower Compartments
Alternate roll-in type shower compartments shall be 36 inches (915 mm) wide and 60 inches (1525 mm) deep minimum clear inside dimensions measured at center points of opposing sides....
-
1016.6 Openings
Elongated openings should be placed so that the long dimension is perpendicular, or as close to perpendicular as possible, to the dominant direction of travel....
-
11B-703.6.1 Pictogram field
The 6-inch vertical dimension applies to the field, not the symbol. The symbol may be smaller than the field....
-
C101.4 Units of Measurement (Section-by-Section Analysis)
This proposed section is new to the 255 Guidelines, and would clarify dimensions stated in the text of the guidelines or referenced standards....
-
1016.6 Openings
Elongated openings should be placed so that the long dimension is perpendicular, or as close to perpendicular as possible, to the dominant direction of travel....
-
R304.2.1 Turning Space
The 1.5 m (5.0 ft) dimension shall be provided in the direction of the ramp run....
-
5.2.2.1 Transfer Surface Width Recommendations for M302
Rationale for final recommendation The Committee considered the dimensions for rectangular seats in roll-in showers from the 2010 Standards; and the ideal chair width recommended in Architectural...
-
R304.3.1 Turning Space
The 1.5 m (5.0 ft) dimension shall be provided in the direction of the pedestrian street crossing....
-
4.30.4* Raised and Brailled Characters and Pictorial Symbol Signs
The border dimension of the pictogram shall be 6 in (152 mm) minimum in height....
-
Controls
Consider push plates at least 3 inches in the least dimension since they do not require fine motor coordination or visual acuity to operate....
-
10.2.1(3)
Signs that are sized to the maximum dimensions permitted under legitimate local, state or federal regulations or ordinances shall be considered in compliance with 4.30.2 and 4.30.3 for purposes...
-
1016.6 Openings
Elongated openings should be placed so that the long dimension is perpendicular, or as close to perpendicular as possible, to the dominant direction of travel....
-
Knee Clearance: Clearance as Measured from Distal Knee Point - Manual Wheelchair
It references dimensions of clearance height and depth to the distal knee point on a person....
-
Knee Clearance: Clearance as Measured from Anterior-Most Abdomen Point - Manual Wheelchair
It references dimensions of clearance height and depth to the forward-most abdomen point on a person....
-
11B-703.6.1 Pictogram field
The 6-inch vertical dimension applies to the field, not the symbol. The symbol may be smaller than the field....