Where elevator call buttons or keypads are provided, they shall comply with Sections 11B-407.2.1 and 11B-309.4. [2010 ADA Standards] 407.2.1 Call Controls....
Search Results "Shall"
-
11B-407.2.1 Call controls
-
11B-604.4 Seats
Seats shall not be sprung to return to a lifted position. Seats shall be 2 inches (51 mm) high maximum. [2010 ADAS] 604.4 Seats. ...
-
11B-604.4 Seats
Seats shall not be sprung to return to a lifted position. Seats shall be 2 inches (51 mm) high maximum. [2010 ADAS] 604.4 Seats....
-
11B-604.4 Seats
Seats shall not be sprung to return to a lifted position. Seats shall be 2 inches (51 mm) high maximum. [2010 ADA Standards] 604.4 Seats....
-
11B-608.2.1 Transfer type shower compartments
Transfer type shower compartments shall be 36 inches (914 mm) by 36 inches (914 mm) clear inside dimensions measured at the center points of opposing sides and shall have a 36 inch (914...
-
Amenities
There shall be no projections into the required clear opening width lower than 34 inches and 80 inches above the finish floor or ground shall not exceed 4 inches....
-
503.3 Access Aisle
Passenger loading zones shall provide access aisles complying with 503 adjacent to the vehicle pull-up space....
-
408.1 General
Limited-use/limited-application elevators shall comply with 408 and with ASME A17.1 (incorporated by reference, see "Referenced Standards" in Chapter 1)....
-
607.5 Controls
Controls, other than drain stoppers, shall be located on an end wall....
-
303.1 General
Where changes in level are permitted in floor or ground surfaces, they shall comply with 303. EXCEPTIONS: 1. Animal containment areas shall not be required to comply with 303. 2....
-
303.1 General
Where changes in level are permitted in floor or ground surfaces, they shall comply with 303. EXCEPTIONS: 1....
-
408.1 General
Limited-use/limited-application elevators shall comply with 408 and with ASME A17.1 (incorporated by reference, see "Referenced Standards" in Chapter 1)....
-
T402.10 Visual Contrast
The perimeter of the walking surface on ramps and bridgeplates shall be marked by a stripe....
-
407.2.1 Call Controls
Where elevator call buttons or keypads are provided, they shall comply with 407.2.1 and 309.4. Call buttons shall be raised or flush....
-
503.3 Access Aisle
Passenger loading zones shall provide access aisles complying with 503 adjacent to the vehicle pull-up space....
-
604.6 Flush Controls
Flush controls shall be hand operated or automatic. Hand operated flush controls shall comply with 309....
-
3.2.1 General
Where camping units are provided in a campground, section 4.0 and 5.0 shall apply to each camping unit. Camp living areas shall comply with sections 3.2....
-
4.34.5.2(3)
(3) Structural reinforcement or other provisions that will allow installation of grab bars shall be provided in the locations shown in Fig. 47(b)....
-
410.6 Doors and Gates
Platform lifts shall have low-energy power-operated doors or gates complying with 404.3. Doors shall remain open for 20 seconds minimum....
-
11B-803.5 Coat hooks and shelves
Coat hooks provided within the room shall be located within one of the reach ranges specified in Section 11B-308....
-
11B-410.6 Doors and gates
Platform lifts shall have low-energy power-operated doors or gates complying with Section 11B-404.3. Doors shall remain open for 20 seconds minimum....
-
406.4 Landings
Landings shall be provided at the tops of curb ramps. The landing clear length shall be 36 inches (915 mm) minimum....
-
11B-803.5 Coat hooks and shelves
Coat hooks provided within the room shall be located within one of the reach ranges specified in Section 11B-308....
-
11B-233.3.1.2.5 Multi-story residential dwelling units in buildings with no elevator
unit shall be on an accessible route....