The 48 inch (1220 mm) minimum by 36 inch (915 mm) minimum areas and the accessible route shall be permitted to overlap. Figure 406.7 Islands in Crossings...
Search Results "Interior Route"
-
406.7 Islands
-
106 Definitions
The following definitions have been removed as unnecessary, in most cases due to changes in certain scoping or technical requirements: "accessible route," "area of refuge," "automatic door...
-
Entry Points and Seats
When play components are located on an accessible route, the height required to transfer directly to the entry point or seat of a play component has a minimum of 11 inches (280 mm) and a...
-
Shooting Facilities
Shooting Facilities If facilities provide fixed firing positions, at least 5 percent, but not less than one of each type of fixed firing position must be served by an accessible route...
-
1007.1 Accessible means of egress required
In assembly spaces with sloped floors, one accessible means of egress is required from a space where the common path of travel of the accessible route for access to the wheelchair spaces...
-
16. If a play surface is replaced with an accessible surface and the existing ground level play components are not accessible, do the components need to be replaced?
If the alteration to the play area only involves the surfacing, only the surface along accessible routes, clear floor or ground spaces, and maneuvering spaces must comply with the ASTM F...
-
Is Identification of Which Means of Egress Are Available/Closest Necessary?
Simple floor plans of the building indicating the location of and routes to usable circulation paths should be available in alternative formats such as single-line, high-contrast plans....
-
R310 Passenger Loading Zones (Section-by-Section Analysis)
The access aisle must be 1.5 meters (5 feet) wide minimum, extend the entire length of the vehicle pull-up space, and connect to the pedestrian access route....
-
202.4.1 Disproportionate Cost
Costs that may be counted as expenditures required to provide an accessible path of travel may include: (i) costs associated with providing an accessible entrance and an accessible route...
-
208.1.1
The facility may not reduce the required number or dimensions of those spaces or unreasonably increase the length of the accessible route from a parking space to the facility....
-
1008.3 Transfer Systems
Where elevated play components are used to connect to another elevated play component instead of an accessible route, careful consideration should be used in the selection of the play components...
-
11B-1008.3 Transfer systems
Where elevated play components are used to connect to another elevated play component instead of an accessible route, careful consideration should be used in the selection of the play components...
-
Scoping [4.1.3(12)]
Shelves and display units allowing self-service by customers in mercantile occupancies are not required to comply with this section but are required to be on an accessible route....
-
Historic Preservation [4.1.7]
These requirements address accessible routes, ramps, entrances, toilet rooms, access between floors, and displays....
-
9.2* POST OFFICE LOBBIES
Avoid designs that call for, or may necessitate, non-fixed partitions in circulation routes of handicapped people....
-
11B-1008.3 Transfer systems
Where elevated play components are used to connect to another elevated play component instead of an accessible route, careful consideration should be used in the selection of the play components...
-
11B-1008.3 Transfer systems
Where elevated play components are used to connect to another elevated play component instead of an accessible route, careful consideration should be used in the selection of the play components...
-
11B-246.1 General
Automobile access or accessible routes are not required when the enforcing agency determines compliance with this chapter would create an unreasonable hardship as defined in Chapter 2, Section...
-
Willoughby Industries ETW-1445-BS-HC Toilet for 45-degree Chase Wall
crevice-free self-draining flushing rim with positive after fill - Fully enclosed 2 1/2” O.D. trap which shall maintain a minimum 2" seal and pass a 2 1/8” ball - Bead blast finish bowl interior...
-
Sargent 281 Series Cast Iron Door Closer
The 281 series is a complete line of closers for interior and exterior doors with quality and flexibility to meet virtually every application. ...
-
Kawneer North America 260/360/560 Insulclad™ Thermal Entrances
All doors are thermally enhanced with interior cladding, which has the added advantage of enabling dual-color design. ...
-
SDC Z7500 HiTower Pro Series Actuator Controlled Locksets
SDC HiTower® locksets comply with all national and regional building codes for locking interior office, elevator lobby, exit and stairwell fire rated doors, where the use of electric strikes...
-
GE® 24" Standard Clean Free-Standing Electric Range JAS02SNSS
Compliant Weights and Dimensions Approximate Shipping Weight 150 lb Cabinet Width 24 in Net Weight 135 lb Oven Interior...
-
SDC EMLock® Magnetic Lock
The SDC Electromagnetic Lock is Suited For Interior Doors, Perimeter Exit Doors and Entrances that Require Failsafe Emergency Release Capability....
