Swinging door and gate surfaces within 10 inches (255 mm) of the finish floor or ground measured vertically shall have a smooth surface on the push side extending the full width of the door...
Search Results "Hinge Side Clearance"
Filters
Commonly Searched Documents
-
404.2.10 Door and Gate Surfaces
-
505.6 Gripping Surface
Handrail gripping surfaces shall be continuous along their length and shall not be obstructed along their tops or sides....
-
11B-405.5 Clear width
Handrails may project into the required clear width of the ramp at each side 3½ inches (89 mm) maximum at the handrail height. 3. ...
-
11B-505.6 Gripping surface
Handrail gripping surfaces shall be continuous along their length and shall not be obstructed along their tops or sides....
-
501.1 Scope
Applications may be web-based or client-side software....
-
Common Requirements (R304.5) (Section-by-Section Analysis)
Common Requirements (R304.5) (Section-by-Section Analysis) The clear width of curb ramp runs (excluding flared sides), blended transitions, and turning spaces must be 1.2 meters (4 feet...
-
FAQ: Why should I enter ADA references in the content I add to my Corada WorkSpace?
When the reference options are displayed, click on "308.3 Side Reach." Repeat this process until all applicable/desired references are entered. ...
-
2.7 Comparing Visual Detection Rates and High Conspicuity Ratings for Detectable Warnings
Note that when detectable warning color was similar to the side walk color, the number of people who would be served by the visual properties of the detectable warning decreased markedly...
-
Accessible Pathway & Corridor: Minimum Clear Width Required for 90-degree Turn
The other side of each leg had moveable walls. The enclosed space was incrementally increased until a user could pass through the turn successfully....
-
1.1.14 Flatness of ramp cross slope
As the ramp gets wider, users may tend to travel toward one side or the other, especially if the ramp is not a curb ramp and has handrails....
-
Hours and Days of Service
For example, if a provider uses its own paratransit vans during high demand periods, it could use a private contractor or user-side subsidy provider during low demand periods....
-
11B-410.8 Restriction sign
. ◼ ETA Editor's Note There are no requirements for landing size or restriction signs in 2010 ADAS, although the door maneuvering clearance requirements at 404.2.4 should be...
-
R402 Protruding Objects (Section-by-Section Analysis)
Guardrails or other barriers to pedestrian travel must be provided where the vertical clearance on pedestrian circulation paths is less than 2 meters (6.7 feet) high....
-
Maintenance of Accessible Features
The trashcan in an accessible toilet room must not be placed in the required clearances at the door and fixtures....
-
208 Parking Spaces
The vertical clearance at such spaces shall comply with 4.6.5. All such spaces may be grouped on one level of a parking structure....
-
ASME A18.1 Safety Standard [§410.1]
The ASME A18.1 Standard addresses requirements for runway enclosures, electrical equipment and wiring, structural support, headroom clearance (80” minimum), access ramps, pits, and other...
-
Applying the Accessibility Standards to the Plan, Installation, and Maintenance of Ground Level Accessible Routes for Playgrounds
Is the vertical clearance a minimum of 80 inches for the ground level accessible route?...
-
11B-410.8 Restriction sign
.◼ ETA Editor's Note There are no requirements for landing size or restriction signs in 2010 ADAS, although the door maneuvering clearance requirements at 404.2.4 should be applicable...
-
Spectra Safety Treads
Nosings shall terminate not more than 4" from ends of steps for poured concrete stairs; for concrete filled steel pan stairs, nosings shall be full length of steps less 1/8" clearance....
-
Guardian Barrier-Free Eyewash: Deck Mounted, AutoFlow™ 90º Swing-Down GBF1849
ADA compliance is dependent on 27” knee clearance under counter and 34” maximum counter height. Spray heads swing down from storage to operational position, activating water flow....
-
AJW Architectural Products UG130-Railing UG130X-Y108 108" Exposed Flange, 1.5" Diameter Grab Bar, Peened Grip - Configuration Y
Strength: Bars with a 1 1/2" offset clearance will support loads in excess of 900lbs when properly installed....
-
AJW Architectural Products UG3-Railing UG3X-Y108 108" Concealed Snap Flange, 1.5" Diameter, Peened Grip - Configuration Y
Strength: Bars with a 1 1/2" offset clearance will support loads in excess of 900lbs when properly installed....
-
AJW Architectural Products UG120-Railing UG120X-Y108 108" Exposed Flange, 1.25" Diameter, Peened Grip - Configuration Y
Strength: Bars with a 1 1/2" offset clearance will support loads in excess of 900lbs when properly installed....
