Landings must be a minimum of 36 inches in width and 60 inches in length. The sloped entry may be a maximum of 30 feet at 1:12 (8.33%) slope before an intermediate landing is required....
Search Results "Seat Width"
Filters
Commonly Searched Documents
-
Submerged Depth
-
1002.4.4.2 Side Entry
A 32 inch (815 mm) clear opening will not provide sufficient width when entered through a turn into an amusement ride....
-
1002.4.4.2 Side Entry
A 32 inch (815 mm) clear opening will not provide sufficient width when entered through a turn into an amusement ride....
-
1132A.9 Smooth surface
Swinging door or gate surfaces within 10 inches (254 mm) of the finish floor or ground measured vertically shall have a smooth surface on the push side extending the full width of the door...
-
Edge Protection
Recommendation: At narrow routes in particular, consider maintenance of adjacent surfaces as raised or flush or wider route widths in consideration of minimum maneuvering and passage requirements...
-
Rough Form and Foundation Inspection
slope). 11B-403 Verify forms for sidewalks, ramps, landings, curb ramps and clear floor spaces are correctly installed so proper slopes, cross slopes, widths...
-
Floor Plan of Elevator Cars [4.10.9]
In alterations, smaller car sizes (minimum 47 inch width and 69 inch length) are permitted in cases of technical infeasibility, including where limited by existing shaft configurations (...
-
Shape and Diameter
A gripping surface width between 1¼ to 1½ inches diameter is specified....
-
Rough Form and Foundation Inspection
slope). 11B-403 Verify forms for sidewalks, ramps, landings, curb ramps and clear floor spaces are correctly installed so proper slopes, cross slopes, widths...
-
4.34.6.7* OVENS
For side-opening ovens, the door latch side shall be next to the open counter space, and there shall be a pull-out shelf under the oven extending the full width of the oven and pulling out...
-
1.1.12 Ramp cross slope
slope of ramps by establishing elevations at the extreme edges of the ramp at the top and bottom of the ramp and calculate the cross slope at these two locations using the horizontal ramp width...
-
11B-1002.4.4.2 Side entry
A 32 inch (815 mm) clear opening will not provide sufficient width when entered through a turn into an amusement ride....
-
11B-1002.4.4.2 Side entry
A 32 inch (815 mm) clear opening will not provide sufficient width when entered through a turn into an amusement ride....
-
11B-704.2.1.2 Forward approach
If an additional 6 inches (152 mm) in width of clear floor space is provided, creating a clear floor space of 36 inches by 48 inches (914 mm by 1219 mm), the enclosure may extend more than...
-
Section 36.303(g)(1) Captioning Device
Captioning Device” In the NPRM, at proposed § 36.303(g)(1)(iv), the Department used the term “individual captioning device” to refer to the “individual device that patrons may use at their seats...
-
§27.72(b)
This section applies to all aircraft with a passenger capacity of 19 or more passenger seats, except as provided in paragraph (e) of this section....
-
What kinds of securement equipment must be provided in buses and vans?
Section 38.23(d) of the DOT ADA regulations requires all ADA-compliant buses and vans to have a two-part securement system, one to secure the wheelchair, and a seat belt and shoulder...
-
What kinds of securement equipment must be provided in buses and vans?
Section 38.23(d) of the DOT ADA regulations requires all ADA-compliant buses and vans to have a two-part securement system, one to secure the wheelchair, and a seat belt and shoulder harness...
-
12182(b)(2)(C)(ii)
(ii) the purchase or lease by such entity for use on such system of a vehicle with a seating capacity in excess of 16 passengers (including the driver), for which solicitations are made...
-
§ 38.111(a)(2)
this part, to provide table service to a person who wishes to remain in his or her wheelchair, and space to fold and store a wheelchair for a person who wishes to transfer to an existing seat...
-
Sargent HC 8800 Rim Exit Device
The HC8800 device is designed for standard width stile applications on metal doors. The Hurricane Code Hardware has been accepted by Dade County, Florida....
-
1015.2 Where required
In assembly seating areas at cross aisles in accordance with Section 1029.12. On the loading side of station platforms on fixed guideway transit or passenger rail systems....
-
Just Manufacturing Wall Mounted Sink Faucet with Pail Hook and Vacuum Breaker
Replaceable seats and Buna-N seat washers. Replaceable reinforced nitrile rubber packing. Chrome plated die cast lever handles....
