BTX prides itself on being able to offer the height of design, better heating and air conditioning energy conservation, and the convenient control that patrons have come to know and expect...
Search Results "Character Height (Visual)"
Filters
Commonly Searched Documents
-
BTX Intelligent Fashion Motorized Drapery Systems
-
1. Width and Depth of Wheelchair Spaces
Because the final rule also requires raised platforms over 1½ inches in height to provide edge protection that is a minimum of 2 inches high from the surface of the platform (See M303.2.6...
-
II. Rulemaking History
The committee members reached a consensus on all of their recommendations, except for the recommended lowest or minimum height for adjustable-height transfer surfaces....
-
Meeting ANSI Standard S12.60 Requirements
For classrooms where there is no fixed lecture position for the teacher, such as those for lower grades, and where ceiling heights are less than ten feet, the best option is to place most...
-
1.3.1 Overview of NPRM
Equipment to Which Technical Criteria Applies Diagnostic Equipment Used by Patients in Supine, Prone, or Side-Lying Position (M301) Transfer surface, including height...
-
Road Roughness Measurements
(Figure 8) An inertial profiler uses an accelerometer and a non-contacting sensor, such as a laser transducer, to measure height....
-
M303.2.4 Equipment Clearances (Section-by-Section Analysis)
Due to the reorganization of the equipment clearances provision in the final rule, the knee and toe clearance requirements for the other equipment section have been renamed depth and height...
-
H. Your Obligation to Provide Services and Equipment
[Sec. 382.21(a)(4)] On-board wheelchairs must be equipped with footrests, armrests which are movable or removable, adequate occupant restraint systems, a backrest height that permits assistance...
-
III 3.11000 Insurance
ILLUSTRATION: An amusement park requires individuals to meet a minimum height requirement that excludes some individuals with disabilities for certain rides because of a limitation in its...
-
Standards that measure needed physical or mental ability to perform a job
Possible accommodations might include lowering the shelf-height, providing a step stool or other assistive device....
-
11B-703.3.1 Dimensions and capitalization
dots in the same cell1 0.100 (2.5 mm) Distance between corresponding dots in adjacent cells1 0.300 (7.6 mm) Dot height...
-
11B-404.2.10 Door and gate surfaces
stiles and having a bottom rail or shoe with the top leading edge tapered at 60 degrees minimum from the horizontal shall not be required to meet the 10 inch (254 mm) bottom smooth surface height...
-
F226.1 General
Consider work surfaces that are flexible and permit installation at variable heights and clearances....
-
404.2.10 Door and Gate Surfaces
stiles and having a bottom rail or shoe with the top leading edge tapered at 60 degrees minimum from the horizontal shall not be required to meet the 10 inch (255 mm) bottom smooth surface height...
-
5.4.2.2 Transfer and Positioning Support Length Recommendations for Imaging Equipment with Transfer Surfaces
A positioning support (for transfer surfaces >24” deep) is to extend horizontally along the side of the patient scanning/imaging bed/table with a length of 12 to 16 inches and a height...
-
Using the ORAR Exceptions [F202.3, Exception 4 and 1016, Exceptions 1, 2, and 3]
instance, where traffic calming devices, gates, or other barriers are provided on a paved roadway, the ORAR must have a clear width of 36 inches and obstacles cannot exceed one-half inch in height...
-
Seat Width Evaluation
seat was the smallest of the platform seat widths available in this study and was suitable for many participants (the 25th through 95th percentiles) for their level, highest and lowest height...
-
Alterations
is defined as remodeling, renovating, rehabilitating, reconstructing, changing or rearranging structural parts or elements, changing or rearranging plan configuration of walls and full-height...
-
The Purpose of FSORAG and FSTAG
included (scoping); what has to comply with the guidelines; definitions of terms; and technical requirements defining the physical characteristics of accessible features, such as width, height...
-
4.16.6 Dispensers
As a result, the dispenser was located 24" above the floor, 5" higher than the minimum height in ADAAG, and 42" from the rear wall (Figure 13), which would have been too high and too far...
-
Additional Features of Van-Accessible Parking Spaces
Vertical clearance of 98 inches minimum to accommodate van height at the vehicle parking space, the adjacent access aisle, and on the vehicular route to and from the van-accessible space...
-
11B-703.3.1 Dimensions and capitalization
1.6 mm) Distance between two dots in the same cell1 0.100 (2.5 mm) Distance between corresponding dots in adjacent cells1 0.300 (7.6 mm) Dot height...
-
11B-404.2.10 Door and gate surfaces
stiles and having a bottom rail or shoe with the top leading edge tapered at 60 degrees minimum from the horizontal shall not be required to meet the 10 inch (254 mm) bottom smooth surface height...
-
11B-404.2.10 Door and gate surfaces
stiles and having a bottom rail or shoe with the top leading edge tapered at 60 degrees minimum from the horizontal shall not be required to meet the 10 inch (254 mm) bottom smooth surface height...