Provisions require transfer supports be provided for use with the transfer sides and be located within reach of the transfer surface and not obstruct transfer onto the surface when in position...
Search Results "Braille Position"
Filters
Commonly Searched Documents
-
5.4.1 Transfer Support Location for M301 and M302
-
407.4.7.1.2 Location
Raised character and braille designations shall be placed immediately to the left of the control button to which the designations apply....
-
11B-407.4.7.1.2 Location
Raised characters or symbols and Braille designations shall be placed immediately to the left of the control button to which the designations apply....
-
11B-407.4.7.1.2 Location
Raised characters or symbols and Braille designations shall be placed immediately to the left of the control button to which the designations apply....
-
Dancing Dots - Valley Forge, PA
With GOODFEEL® combined with a few mainstream products, any sighted musician can prepare a braille score without needing to be a Braille music specialist....
-
M302.2.1 Height
The transfer surface is permitted to be positioned outside of the specified height range when not needed to facilitate transfer....
-
Destination-Oriented Elevators
provisions unique to destination-oriented elevators: Elevator Door Requirements (§407.3) Specifications for door and signal timing do not apply (§407.3.4, Ex. 2) Car Position...
-
M305.2.8 Fittings (Section-by-Section Analysis)
Another commenter (manufacturer) pointed out that bed rails, which are common on hospital beds, require a latched position and an unlatched position, which allows them to rotate in their...
-
5.4.10 Transfer Support Fittings Recommendations for M301 and M302
When the transfer supports latch into a locked position, the transfer supports must meet the required load conditions without movement....
-
M101.2 Application
Where diagnostic equipment is designed to support more than one patient position, the standards for each patient position supported shall be applied to the equipment....
-
1010.1.9.8.1 Delayed egress locking system
A tactile sign shall also be provided in Braille and raised characters, which complies with Chapter 11B, Sections 11B-703.1, 11B-703.2, 11B-703.3 and 11B-703.5....
-
M305.4 Leg Supports
Leg supports shall provide a method of supporting, positioning, and securing the patient’s legs....
-
5.4.7 Transfer Support Gripping Surface Clearance Recommendation for M301 and M302
considering whether 1½ inches minimum clearance around the gripping surface would be appropriate for transfer supports on diagnostic equipment used by patients in a supine, prone, or side-lying position...
-
5.4.4 Transfer Support Distance from Transfer Surface Recommendations for M301 and M302
Surface Recommendations for M301 and M302 Description: This minimum distance ensures that the transfer support is within reach of the transfer surface and can be effectively used to position...
-
ADA Sign Depot Exit Sign with Tactile Text and Grade 2 Braille - 5" x 3"
non-glare matte finish ADA compliant font and tactile (1/32 inch raised) letters ADA compliant 5x3 size and 1-inch letter height ADA compliant California domed Grade 2 Braille...
-
1023.9 Stairway identification signs
The bottom of the sign shall be located not less than 5 feet (1524 mm) above the floor landing in a position that is readily visible when the doors are in the open and closed positions....
-
iv. Lifts
iv. Lifts Medical providers may need lifts to transfer some patients with mobility disabilities safely to examination or treatment tables or chairs or to gurneys or hospital beds....
-
5.2.1.1 Transfer Surface Width
The transfer surface should be 28 inches wide minimum for equipment used by patients in a supine, side-lying, or prone position....
-
5.2.1.2 Transfer Surface Depth
The transfer surface should be 17 inches deep minimum for all equipment used by patients in a supine, side-lying, or prone position with the exception of imaging equipment....
-
5.2.1.4 Transfer Surface Size for Imaging Equipment
5.2.1.4 Transfer Surface Size for Imaging Equipment. The transfer surface should be 28 inches wide minimum and 21 inches deep minimum. The transfer surface should be located such...
-
M301.2.2 Transfer Surface Size
M301.2.2 Transfer Surface Size Subcommittee Recommendation: (Also agreed to by the full committee). A. The minimum size of the transfer surface is 28 inches wide minimum and 21...
-
M305.2.3 Height (Section-by-Section Analysis)
Additionally, for transfer surfaces that are greater than 24 inches deep, the MDE Advisory Committee recommended requiring a positioning support instead of a transfer support, with a height...
-
(2) Transfer Surface Location for Diagnostic Equipment Used in the Seated Position
Commenters also raised concerns with the provisions in the MDE NPRM related to transferring to medical diagnostic equipment used by patients in the seated position....
-
11B-411.4.7 Designations and indicators of car control buttons
Designations and indicators of car control buttons shall comply with Section 11B-411.4.7.
