The map includes a bar code that allows the pedestal to "recognize" the visitor; once identified, the pedestal displays a large, bright You are Here marker, which shows through the translucent...
Search Results "Grab Bar Height"
-
Map-kiosk hybrid
- Big John Commode Chair BJBC
-
Number of Accessible Guest Rooms
Accessible guest rooms include features such as grab bars and other elements that benefit not only people who use wheelchairs, but also people who use crutches, canes, and walkers....
-
Identification of accessible features in hotels and guest rooms. (Section-by-Section Analysis)
the hotel and staff located off-site at a reservations center) should be available to provide additional information such as the specific layout of the room and bathroom, shower design, grab-bar...
-
EXHIBIT F ADA Maintenance Checklist
., toilet, grab bars, toilet paper dispenser)?___ Yes ___ No f. Are the drain line and hot water supply lines insulated so they will not burn a customer's leg?...
- Inclusion Solutions Voter Parking Sign
-
III-4.4200 Readily achievable barrier removal
9) Installing offset hinges to widen doorways; 10) Eliminating a turnstile or providing an alternative accessible path; 11) Installing accessible door hardware; 12) Installing grab...
- Inclusion Solutions Alternate Entrance Double Sided Sign
- Hoyer Journey Stand-Up Lift
- Cybex Total Access Recumbent Bike
-
Standards that measure needed physical or mental ability to perform a job
Possible accommodations might include lowering the shelf-height, providing a step stool or other assistive device....
-
11B-703.3.1 Dimensions and capitalization
dots in the same cell1 0.100 (2.5 mm) Distance between corresponding dots in adjacent cells1 0.300 (7.6 mm) Dot height...
-
11B-404.2.10 Door and gate surfaces
stiles and having a bottom rail or shoe with the top leading edge tapered at 60 degrees minimum from the horizontal shall not be required to meet the 10 inch (254 mm) bottom smooth surface height...
-
404.2.10 Door and Gate Surfaces
stiles and having a bottom rail or shoe with the top leading edge tapered at 60 degrees minimum from the horizontal shall not be required to meet the 10 inch (255 mm) bottom smooth surface height...
-
5.4.2.2 Transfer and Positioning Support Length Recommendations for Imaging Equipment with Transfer Surfaces
A positioning support (for transfer surfaces >24” deep) is to extend horizontally along the side of the patient scanning/imaging bed/table with a length of 12 to 16 inches and a height...
-
Using the ORAR Exceptions [F202.3, Exception 4 and 1016, Exceptions 1, 2, and 3]
instance, where traffic calming devices, gates, or other barriers are provided on a paved roadway, the ORAR must have a clear width of 36 inches and obstacles cannot exceed one-half inch in height...
-
Alterations
is defined as remodeling, renovating, rehabilitating, reconstructing, changing or rearranging structural parts or elements, changing or rearranging plan configuration of walls and full-height...
-
3.3 Equipment Barriers and Solutions
., a bright color against a dark background on the adjustment features, such as the weight amount or seat height and labels that are raised Some parts of the equipment stick...
-
The Purpose of FSORAG and FSTAG
included (scoping); what has to comply with the guidelines; definitions of terms; and technical requirements defining the physical characteristics of accessible features, such as width, height...
-
Car Controls [4.10.12]
Alignment for a side reach is often difficult at panels on the front of cars due to the limited maneuvering space; consider a maximum height of 48 inches for panels on the front of cars....
-
Additional Features of Van-Accessible Parking Spaces
Vertical clearance of 98 inches minimum to accommodate van height at the vehicle parking space, the adjacent access aisle, and on the vehicular route to and from the van-accessible space...
-
11B-703.3.1 Dimensions and capitalization
1.6 mm) Distance between two dots in the same cell1 0.100 (2.5 mm) Distance between corresponding dots in adjacent cells1 0.300 (7.6 mm) Dot height...
-
11B-404.2.10 Door and gate surfaces
stiles and having a bottom rail or shoe with the top leading edge tapered at 60 degrees minimum from the horizontal shall not be required to meet the 10 inch (254 mm) bottom smooth surface height...