Handrail gripping surfaces with a circular cross section shall have an outside diameter of 1¼ inches (32 mm) minimum and 2 inches (51 mm) maximum....
Search Results "Enhanced 9-1-1"
Filters
Commonly Searched Documents
-
11B-505.7.1 Circular cross section
-
4.2.1* Wheelchair Passage Width
The minimum clear width for single wheelchair passage shall be 32 in (815 mm) at a point and 36 in (915 mm) continuously (see Fig. 1 and 24(e))....
-
E1-4. Accessible Route Slope
Where the slope of the accessible route is greater than 1:20, does this part of the accessible route meet the following requirements for an accessible ramp? Yes _____ No _____...
-
7.4.4 Resting Intervals
Where the trail grade exceeds 1:20 (5 percent), resting intervals shall be provided as specified in Table 7.4.3.1....
-
4.2.1* WHEELCHAIR PASSAGE WIDTH
The minimum clear width for single wheelchair passage shall be 32 in (815 mm) at a point and 36 in (915 mm) continuously (see Fig. 1 and 24(e))....
-
11B-1010.1 Turning space
A circular turning space 60 inches (1524 mm) diameter minimum with slopes not steeper than 1:48 shall be provided at shooting facilities with firing positions....
-
11B-406.3.1 Slope
Ramp runs shall have a running slope not steeper than 1:12....
-
11B-504.4 Tread surface
Exception: Treads shall be permitted to have a slope not steeper than 1:48....
-
11B-505.7.1 Circular cross section
Handrail gripping surfaces with a circular cross section shall have an outside diameter of 1¼ inches (32 mm) minimum and 2 inches (51 mm) maximum....
-
11B-706.2 Receiver jacks
Receivers required for use with an assistive listening system shall include a 1/8 inch (3.2 mm) standard mono jack....
-
11B-809.8.1 Door Thresholds
Secondary exterior door thresholds, including sliding door tracks, shall be 3/4 inch (19.1 mm) high maximum with a 1:2 maximum slope....
-
11B-505.7.1 Circular cross section
Handrail gripping surfaces with a circular cross section shall have an outside diameter of 1¼ inches (32 mm) minimum and 2 inches (51 mm) maximum....
-
11B-1010.1 Turning space
A circular turning space 60 inches (1524 mm) diameter minimum with slopes not steeper than 1:48 shall be provided at shooting facilities with firing positions....
-
11B-406.3.1 Slope
Ramp runs shall have a running slope not steeper than 1:12....
-
End note
[FR Doc. 2011-23576 Filed 9-15-11; 11:15 am] BILLING CODE 4910-9X-P...
-
§ 36.104 Definitions
9. Amend § 36.104 by revising the definition of ‘‘Disability’’ to read as follows: § 36.104 Definitions. * * * * * Disability....
-
11B-308.4 Suggested reach ranges for children
USE SUGGESTED REACH RANGES FOR CHILDREN AGES 3 THROUGH 12 Forward or Side Reach Ages 3 and 4 Ages 5 through 8 Ages 9...
-
11B-604.7 Dispensers and disposal units
Toilet paper dispensers shall comply with 309.4 and shall be 7 inches (180 mm) minimum and 9 inches (230 mm) maximum in front of the water closet measured to the centerline of the dispenser...
-
Horse Accessible Gates
This gate is not accessible because it is narrower than the minimum width required for passage of a wheelchair (32 inches) and the bar across the opening is higher than 1 inch....
-
Accessible Amusement Rides
Bush, New Freedom Initiative, February 1, 2001 The recreation facility guidelines described in this guide focus on newly designed or newly constructed and altered amusement rides....
-
Resting Intervals [1017.8]
Resting intervals are required between trail segments any time the running slope exceeds 1:20 (5 percent)....
-
Resting Intervals [1016.8]
Resting intervals are required at the top and bottom of an ORAR section any time the running slope exceeds 1:20 (5 percent)....
-
§8.3 Program or activity
Program or activity means all of the operations of: (a)(1) A department, agency, special purpose district, or other instrumentality of a State or of a local government; or (2) The...
-
10.3.2(4)
key stations, the platform or a portion thereof and the vehicle floor shall be coordinated so that the vertical difference, measured when the vehicle is at rest, is within plus or minus 1‒...