Grab bars with circular cross sections shall have an outside diameter of 1¼ inches (32 mm) minimum and 2 inches (51 mm) maximum....
Search Results "Enhanced 9-1-1"
Filters
Commonly Searched Documents
-
609.2.1 Circular Cross Section
-
802.1.1 Floor or Ground Surface
EXCEPTION: Slopes not steeper than 1:48 shall be permitted....
-
M305.2.4.1 Circular Cross Section
Transfer supports with circular cross sections shall have an outside diameter of 1 ¼ inches (32 mm) minimum and 2 inches (51 mm) maximum....
-
M303.3.2 Beveled
Changes in level between ¼ inch (6.4 mm) high and ½ inch (13 mm) high maximum shall be beveled with a slope not steeper than 1:2....
-
802.1.1 Floor or Ground Surface
EXCEPTION: Slopes not steeper than 1:48 shall be permitted....
-
409.4.4 Leveling
Each car shall automatically stop at a floor landing within a of 1/2 inch (13 mm) under rated loading to zero loading conditions....
-
Individual captioning device (Section-by-Section Analysis)
In § 36.303(g)(1)(iv), the Department is proposing to define “individual captioning device” as “the individual device that patrons may use at their seats to view the closed captions.”...
-
T303.3.2 Handrail and Stanchion Circular Cross Section
Handrails and stanchions with a circular cross section shall have an outside diameter of 1¼ inches (32 mm) minimum and 2 inches (50 mm) maximum....
-
Figure 11B-407.2.3.1 Floor designation
Revises the braille designation on the figure to correctly indicate the number 1 and revises figure title....
-
706.2 Receiver Jacks
Receivers required for use with an assistive listening system shall include a 1/8 inch (3.2 mm) standard mono jack....
-
11B-609.2.1 Circular cross section
Grab bars with circular cross sections shall have an outside diameter of 1¼ inches (32 mm) minimum and 2 inches (51 mm) maximum....
-
Sec. 12164. Regulations. [Section 244]
Not later than 1 year after July 26, 1990, the Secretary of Transportation shall issue regulations, in an accessible format, necessary for carrying out this subpart....
-
505.5 Clearance
Clearance between handrail gripping surfaces and adjacent surfaces shall be 1½ inches (38 mm) minimum. Figure 505.5 Handrail Clearance...
-
407.4.3 Platform to Hoistway Clearance
The clearance between the car platform sill and the edge of any hoistway landing shall be 1¼ inch (32 mm) maximum....
-
12143(b) Issuance of regulations
(b) Issuance of regulations Not later than 1 year after July 26, 1990, the Secretary shall issue final regulations to carry out this section....
-
406.3 Sides of Curb Ramps
Where provided, curb ramp flares shall not be steeper than 1:10. Figure 406.3 Sides of Curb Ramps...
-
410.6.3.1 PSTN
Where ICT interoperates with the Public Switched Telephone Network (PSTN), real-time text shall conform to TIA 825-A (incorporated by reference in Chapter 1)....
-
A Guide to Planning Accessible Meetings
version 1.0 7/1/2015 Helping you navigate, plan and create accessible meetings, events, and conferences that serve all your guests' needs....
-
M303.3.2 Beveled
Changes in level between ¼ inch (6.4 mm) high and ½ inch (13 mm) high maximum shall be beveled with a slope not steeper than 1:2....
-
DIRECTIONAL SIGN
[DSA-AC, HCD 1 & HCD 2]. A publicly displayed notice which indicates by use of words or symbols a recommended direction or route of travel....
-
§ 38.153(c)(2) Exception
Where compliance with the door width requirement of paragraph (c)(1) of this section is not feasible, the minimum door width shall be 27 in (685 mm)....
-
11B-609.2.1 Circular cross section
Grab bars with circular cross sections shall have an outside diameter of 1¼ inches (32 mm) minimum and 2 inches (51 mm) maximum....
-
11B-504.4 Tread surface
Changes in level, slopes exceeding 1:48, and detectable warnings shall not be permitted. Exception: Reserved....
-
DIRECTIONAL SIGN
[DSA-AC, HCD 1 & HCD 2]. A publicly displayed notice which indicates by use of words or symbols a recommended direction or route of travel....