The entrance to the toilet shall be level with the surrounding surface....
Search Results "Surface"
Filters
Commonly Searched Documents
-
5.3.6 Entrance
-
4.9.4(2)
At the top, the extension shall be parallel with the floor or ground surface....
-
4.6.3* Parking Spaces
Parking spaces and access aisles shall be level with surface slopes not exceeding 1:50 (2%) in all directions....
-
Alteration of a recreation site, building, or facility
Alterations include, but are not limited to, remodeling, renovation, rehabilitation, reconstruction, historic restoration, change in surface of circulation paths or vehicular ways, changes...
-
5.3.6 Entrance
The entrance to the toilet shall be level with the surrounding surface....
-
1016.6 Openings
Openings in the surface of outdoor recreation access routes shall not allow the passage of a sphere more than 1/2 inch (13 mm) in diameter. Advisory 1016.6 Openings....
-
Error/Omission: Landing areas where ramps change direction (e.g., switchbacks or 90° turns) are too small.
Result: Wheelchair users are unable to go up or down the ramp because there is not enough space to turn on a level surface. This makes the ramp unusable....
-
11B-703.7.2.7 Pedestrian traffic-control buttons
Control buttons shall be located no higher than 48 inches (1219 mm) above the ground surface adjacent to the pole....
-
1002.6 Transfer Devices for Use with Amusement Rides
Where possible, designers are encouraged to locate the transfer device seat no higher than 17 to 19 inches (430 to 485 mm) above the load and unload surface....
-
11B-1002.6 Transfer devices for use with amusement rides
Where possible, designers are encouraged to locate the transfer device seat no higher than 17 to 19 inches (430 to 485 mm) above the load and unload surface....
-
1002.6 Transfer Devices for Use with Amusement Rides
Where possible, designers are encouraged to locate the transfer device seat no higher than 17 to 19 inches (430 to 485 mm) above the load and unload surface....
-
When Ramps Are Required
Rise of a ramp is the amount of vertical distance the inclined or slanted surface ascends or descends....
-
R210.3 Shared Use Paths
Objects shall not overhang or protrude into any portion of a shared use path at or below 2.4 m (8.0 ft) measured from the finish surface....
-
Alternative Golf Car Passage
While a golf car passage must be usable by golf cars, it does not necessarily need to have a prepared surface and may be part of a golf car path....
-
1002.6 Transfer Devices for Use with Amusement Rides
Where possible, designers are encouraged to locate the transfer device seat no higher than 17 to 19 inches (430 to 485 mm) above the load and unload surface....
-
4. Wheelchair seat depth
The median seat depth across different wheeled mobility devices would provide a reference value for the depth of other common seating surfaces....
-
COSTS TO LOWER MINIMUM TABLE HEIGHT
The need to reach heights above 32 inches interferes with efforts to lower the transfer surface height....
-
Initial Measures and Transfer Setup
This approach is also widely promoted in rehabilitation research (A Clinical Application Guide to Standardized Wheelchair Seating Measurements of the Body and Seating Support Surfaces, See...
-
3. FIXTURES and HARDWARE
If self-closing valves are used, the faucet shall remain open for at least 10 seconds.”xxii Sinks Exposed Pipes and Surfaces: Hot water and drain pipes under lavatories...
-
The Purpose of FSORAG and FSTAG
has to comply with the guidelines; definitions of terms; and technical requirements defining the physical characteristics of accessible features, such as width, height, slope, length, surface...
-
Standardized Tests of Physical Fitness and Community Ambulation
The subjects rated the level of difficulty from 1 to 10 for both straight travel and turning on the surface using the Level of Difficulty Rating Scale....
-
Multiple Parking Facilities on a Site
., surface lot versus parking garage or deck); dedicated to, and separately serve, different facilities on a site; segmented and separated by guard rails, fencing, or barriers...
-
11B-1002.6 Transfer devices for use with amusement rides
Where possible, designers are encouraged to locate the transfer device seat no higher than 17 to 19 inches (430 to 485 mm) above the load and unload surface....
-
11B-1002.6 Transfer devices for use with amusement rides
Where possible, designers are encouraged to locate the transfer device seat no higher than 17 to 19 inches (430 to 485 mm) above the load and unload surface....