Excluding a service animal from an OR or similar special care areas (e.g., burn units, some ICUs, PE units, and any other area containing equipment critical for life support) is appropriate...
Search Results "Unit of Measurement"
-
3. Service Animals
-
Section 36.304 Removal of Barriers (Preamble, Section-by-Section Analysis)
Moreover, the inclusion of a measure on this list does not mean that it is readily achievable in all cases....
-
§382.3 Air transportation
Generally this refers to transportation by aircraft within, to or from the United States....
-
2.5
2.5 In any third party litigation involving Cinemark's stadium-style movie theaters, the United States shall not advocate a position that contradicts or calls into question the terms...
-
§ 382.3 Air Transportation
Generally this refers to transportation by aircraft within, to or from the United States. * * * * *...
-
E.6.iv. - Do vendor web sites advertising EIT products or providing information about EIT products to the federal government have to meet the Section 508 standards?
Section 508 applies to Federal departments or agencies, including the United States Postal Service....
-
4.1.3(12)(b)
(b) Shelves or display units allowing self-service by customers in mercantile occupancies shall be located on an accessible route complying with 4.3....
-
A9.2 POST OFFICE LOBBIES
Furniture as chattel is not covered under the Architectural Barriers Act of 1968, but the requirements for lobby furniture and equipment are imposed by the United States Postal Service for...
-
§100.205(g)(2)
(2) A State or unit of general local government may review and approve newly constructed multifamily dwellings for the purpose of making determinations as to whether the requirements of...
-
§100.205(h)
(h) Determinations of compliance or noncompliance by a State or a unit of general local government under paragraph (f) or (g) of this section are not conclusive in enforcement proceedings...
-
11B-704.2.1.1 Parallel approach
Where a parallel approach is provided, the distance from the edge of the telephone enclosure to the face of the telephone unit shall be 10 inches (254 mm) maximum....
-
11B-602.5 Spout location
The spout shall be located 15 inches (381 mm) minimum from the vertical support and 5 inches (127 mm) maximum from the front edge of the unit, including bumpers....
-
602.5 Spout Location
The spout shall be located 15 inches (380 mm) minimum from the vertical support and 5 inches (125 mm) maximum from the front edge of the unit, including bumpers....
-
BACKGROUND
Plaintiff United States of America (“United States”) commenced this action against Defendants Employees’ Retirement Systems of Alabama, Teachers’ Retirement Systems of Alabama (collectively...
-
Vehicle Parking
Design Tip Determine parking requirements for walk-in camping units....
-
11B-306.1 General
Clearances are measured in relation to the usable clear floor space, not necessarily to the vertical support for an element....
-
Urinal Depth
In the proposed rule, the Board sought to clarify the requirement in the original ADAAG that accessible urinals have an "elongated" rim by specifying a minimum dimension of 13 ½ inches, measured...
-
502.6 Identification
Signs shall be 60 inches (1525 mm) minimum above the finish floor or ground surface measured to the bottom of the sign. [ECTCR UFAS 4.6.4] Advisory 502.6 Identification....
-
Cross Slope
Once placed in the water, measurements, absent live loads, are to be made from a static condition (i.e., absence of movement that results from wind, waves, etc.)....
-
R302.6 Cross Slope
The cross slope of the pedestrian access route is measured perpendicular to the direction of pedestrian travel....
-
Side Reach [4.2.6]
High and low reaches are based on a depth of reach no greater than 10 inches measured from the available clear floor space....
-
Surface Textures [4.3.6]
Since there are no uniform test procedure or measurable values for these characteristics (except for slip-resistance), acceptable and unacceptable materials are not easy to categorize....
-
Size and Clearances [4.21.2]
The 36 by 36 inch dimension, measured to the interior finish, keeps front and side grab bars within reach from the seat....
-
3 - Best practices for pre - construction meetings
Unusual or particularly tight tolerances can be discussed, questions asked, construction techniques suggested, measurement methods outlined, and how compliance will be checked can all be...