For classrooms where there is no fixed lecture position for the teacher, such as those for lower grades, and where ceiling heights are less than ten feet, the best option is to place most...
Search Results "Grab Bar Height"
Filters
Commonly Searched Documents
-
Meeting ANSI Standard S12.60 Requirements
-
1.3.1 Overview of NPRM
Equipment to Which Technical Criteria Applies Diagnostic Equipment Used by Patients in Supine, Prone, or Side-Lying Position (M301) Transfer surface, including height...
-
Road Roughness Measurements
(Figure 8) An inertial profiler uses an accelerometer and a non-contacting sensor, such as a laser transducer, to measure height....
-
M303.2.4 Equipment Clearances (Section-by-Section Analysis)
Due to the reorganization of the equipment clearances provision in the final rule, the knee and toe clearance requirements for the other equipment section have been renamed depth and height...
-
H. Your Obligation to Provide Services and Equipment
[Sec. 382.21(a)(4)] On-board wheelchairs must be equipped with footrests, armrests which are movable or removable, adequate occupant restraint systems, a backrest height that permits assistance...
-
III 3.11000 Insurance
ILLUSTRATION: An amusement park requires individuals to meet a minimum height requirement that excludes some individuals with disabilities for certain rides because of a limitation in its...
-
1023.9 Stairway identification signs
comply with Chapter 11B shall be located at the landing of each floor level, placed adjacent to the door on the latch side, in all enclosed stairways in buildings two or more stories in height...
-
Inclusion Solutions Voter Parking Sign
Sign Height: 14 inches. Portable, lightweight signs can solve parking and other Election Day accessibility issues....
-
Standards that measure needed physical or mental ability to perform a job
Possible accommodations might include lowering the shelf-height, providing a step stool or other assistive device....
-
11B-703.3.1 Dimensions and capitalization
dots in the same cell1 0.100 (2.5 mm) Distance between corresponding dots in adjacent cells1 0.300 (7.6 mm) Dot height...
-
11B-404.2.10 Door and gate surfaces
stiles and having a bottom rail or shoe with the top leading edge tapered at 60 degrees minimum from the horizontal shall not be required to meet the 10 inch (254 mm) bottom smooth surface height...
-
404.2.10 Door and Gate Surfaces
stiles and having a bottom rail or shoe with the top leading edge tapered at 60 degrees minimum from the horizontal shall not be required to meet the 10 inch (255 mm) bottom smooth surface height...
-
5.4.2.2 Transfer and Positioning Support Length Recommendations for Imaging Equipment with Transfer Surfaces
A positioning support (for transfer surfaces >24” deep) is to extend horizontally along the side of the patient scanning/imaging bed/table with a length of 12 to 16 inches and a height...
-
Using the ORAR Exceptions [F202.3, Exception 4 and 1016, Exceptions 1, 2, and 3]
instance, where traffic calming devices, gates, or other barriers are provided on a paved roadway, the ORAR must have a clear width of 36 inches and obstacles cannot exceed one-half inch in height...
-
Alterations
is defined as remodeling, renovating, rehabilitating, reconstructing, changing or rearranging structural parts or elements, changing or rearranging plan configuration of walls and full-height...
-
3.3 Equipment Barriers and Solutions
., a bright color against a dark background on the adjustment features, such as the weight amount or seat height and labels that are raised Some parts of the equipment stick...
-
The Purpose of FSORAG and FSTAG
included (scoping); what has to comply with the guidelines; definitions of terms; and technical requirements defining the physical characteristics of accessible features, such as width, height...
-
Car Controls [4.10.12]
Alignment for a side reach is often difficult at panels on the front of cars due to the limited maneuvering space; consider a maximum height of 48 inches for panels on the front of cars....
-
Additional Features of Van-Accessible Parking Spaces
Vertical clearance of 98 inches minimum to accommodate van height at the vehicle parking space, the adjacent access aisle, and on the vehicular route to and from the van-accessible space...
-
11B-703.3.1 Dimensions and capitalization
1.6 mm) Distance between two dots in the same cell1 0.100 (2.5 mm) Distance between corresponding dots in adjacent cells1 0.300 (7.6 mm) Dot height...
-
11B-404.2.10 Door and gate surfaces
stiles and having a bottom rail or shoe with the top leading edge tapered at 60 degrees minimum from the horizontal shall not be required to meet the 10 inch (254 mm) bottom smooth surface height...
-
1010.1.9.8.1 Delayed egress locking system
Sign lettering shall be at least 1 inch (25 mm) in height and shall have a stroke of not less than 1/8 inch (3.2 mm). 6.4....
-
11B-703.3.1 Dimensions and capitalization
dots in the same cell1 0.100 (2.5 mm) Distance between corresponding dots in adjacent cells1 0.300 (7.6 mm) Dot height...
-
11B-404.2.10 Door and gate surfaces
stiles and having a bottom rail or shoe with the top leading edge tapered at 60 degrees minimum from the horizontal shall not be required to meet the 10 inch (254 mm) bottom smooth surface height...
