(5)* One passenger elevator complying with 4.10 shall serve each level, including mezzanines, in all multi-story buildings and facilities unless exempted below. If more than one...
Search Results "Vertical Alignment"
-
4.1.3(5)*
-
303.2 Vertical
Changes in level of ¼ inch (6.4 mm) high maximum shall be permitted to be vertical. Figure 303.2 Vertical Change in Level...
-
Accessible Parking
There should be a vertical clearance of at least 98 inches on the vehicular route to the space, at the parking space, and along the vehicular route to an exit....
-
Bosch 3-Point Self-Leveling Alignment Laser GPL 3
Description Three-point plumb and level point projection laser accurately transfers and aligns plumb up/down, front level and align points; accuracy is +/- 1/4 In. at 100 ft....
-
M303.3.1 Vertical
Changes in level of ¼ inch (6.4 mm) high maximum shall be permitted to be vertical....
-
M303.3.1 Vertical
Changes in level of ¼ inch (6.4 mm) high maximum shall be permitted to be vertical....
-
Vertical Transportation
Vertical Transportation Segway devices are permitted on elevators, but are not permitted on escalators, as per manufacturer guidance....
-
303.2 Vertical
Changes in level of 1/4 inch (6.4 mm) high maximum shall be permitted to be vertical....
-
Section A: Parking
, 502.3) Width of space _____ Width of access aisle _____ A3 For van accessible spaces (particularly in a garage or parking structure), is there vertical...
-
Bosch Five-Point Self-Leveling Alignment Laser GPL 5 S
It accurately transfers and aligns level, plumb and 90 degree square points. With its smart pendulum system it self-levels and indicates out-of-level conditions....
-
Components of Accessible Routes
[See subsections ...]
-
11B-303.2 Vertical
Changes in level of ¼ inch (6.4 mm) high maximum shall be permitted to be vertical and without edge treatment. [2010 ADAS] 303.2 Vertical. ...
-
Interior Routes
Exposed edges securely fastened with trim on exposed edge. 11B-302.2 Vertical clearances/protrusions along circulation paths. 11B-307...
-
Interior Routes
Exposed edges securely fastened with trim on exposed edge. 11B-302.2 Vertical clearances/protrusions along circulation paths. 11B-307...
-
11B-703.7.2.6.4 Edges and vertices on geometric symbols
Vertices shall be radiused between 1/8 inch (3.2 mm) minimum and ¼ inch (6.4 mm) maximum....
-
11B.707.7.1.1 Vertically mounted display screen
Where display screens are mounted vertically or tipped away from the viewer less than 30 degrees, the center line of the display screen and other display devices shall be no more than 52...
-
11B.707.7.1.1 Vertically mounted display screen
Where display screens are mounted vertically or tipped away from the viewer less than 30 degrees, the center line of the display screen and other display devices shall be no more than 52...
-
11B-703.7.2.6.4 Edges and vertices on geometric symbols
Vertices shall be radiused between 1/8 inch (3.2 mm) minimum and ¼ inch (6.4 mm) maximum....
-
11B-303.2 Vertical
Changes in level of ¼ inch (6.4 mm) high maximum shall be permitted to be vertical and without edge treatment. [2010 ADAS] 303.2 Vertical. ...
-
11B-303.2 Vertical
Changes in level of ¼ inch (6.4 mm) high maximum shall be permitted to be vertical and without edge treatment. [2010 ADA Standards] 303.2 Vertical....
-
Vertical Surface Discontinuities
Vertical Surface Discontinuities. Vertical differences in level between two adjacent surfaces....
-
§ 35.151(g) Assembly areas
(g) Assembly areas. Assembly areas subject to the proposed standards shall comply with the provisions applicable to assembly areas, including, but not limited to, sections 221 and...
-
§ 35.151(g) Assembly areas.
(g) Assembly areas. Assembly areas subject to this section shall comply with the provisions of the 2010 Standards applicable to assembly areas, including, but not limited to,...
-
Bradley Grab Bars 1 1/2" with Concealed Mounting 812
1½" O.D. heavy duty stainless steel grab bar with concealed mounting: Product Materials FLANGES: 3 1/8" dia. 13 gauge stainless steel. ESCUTCHEONS: 22 gauge stainless...
