Wall switches are used to interface with door operators or other electromechanical hardware. Careful consideration should be given to the location of switches relative to their...
Search Results "Push Side"
Filters
Commonly Searched Documents
-
Sargent Wall and Frame Switch Interface for Door Operators
-
Hager Companies 6" Square Actuator 2-659-0170
ADA Actuators – 6" Square Actuator ISA Logo Only Features: - Hard wired and wireless (hard wired standard) - Beveled edges - Graphics embossed onto the faceplate for...
-
Hager Companies 1.5" x 4.75" Jamb Actuator 2-659-0176
ADA Actuators – 1.5" x 4.75" Jamb Actuator ISA Logo Only Features: - Hard wired and wireless (hard wired standard) - Beveled edges - Graphics embossed onto the faceplate for...
-
Hager Companies 4.5" Square Actuator 2-659-0173
ADA Actuators – 4.5" Square Actuator with ISA Logo Only Features: - Hard wired and wireless (hard wired standard) - Beveled edges - Graphics embossed onto the faceplate for...
-
Figure 404.2.4.1(a) Maneuvering Clearances at Manual Swinging Doors and Gates: Front Approach, Pull Side – Drawing from the U.S. Access Board
-
Don-Jo Mfg., Inc. 5" Hospital Latch 4550
Material Brass Size 2-3/4" x 4-1/2" Shelf pack 1 Features UL Listed, Works with 1-3/4" doors, Lever projection 3-1/4", Non Handed, Push...
-
Don-Jo Mfg., Inc. 2-3/4" Hospital Latch 4500
Material Brass Size 2-3/4" x 4-1/2" Shelf pack 1 Features UL Listed, Works with 1-3/4" doors, Lever projection 3-1/4", Non Handed, Push...
-
406.5 Location
Curb ramps and the flared sides of curb ramps shall be located so that they do not project into vehicular traffic lanes, parking spaces, or parking access aisles....
-
4.16.4* Grab Bars
Grab bars for water closets not located in stalls shall comply with 4.26 and Fig. 29. The grab bar behind the water closet shall be 36 in (915 mm) minimum.
-
4.16.4* GRAB BARS
Grab bars for water closets not located in stalls shall comply with Fig. 29 and 4.26.
-
11B-406.5.10 Diagonal curb ramps
Diagonal curb ramps with flared sides shall have a segment of curb 24 inches (610 mm) long minimum located on each side of the curb ramp and within the marked crossing....
-
Wheelchair Transfer
ADAAG specifications are based on three types of transfer: diagonal, perpendicular, and side, some of which are illustrated in ADAAG Appendix Figure A6....
-
M301 Diagnostic Equipment Used by Patients in Supine, Prone, or Side-Lying Position; M302 Diagnostic Equipment Used by Patients in Seated Position
M301 provides technical criteria for diagnostic equipment used by patients in a supine, prone, or sidelying position, and M302 provides technical criteria for diagnostic equipment used by...
-
11B-406.5.10 Diagonal curb ramps
Diagonal curb ramps with flared sides shall have a segment of curb 24 inches (610 mm) long minimum located on each side of the curb ramp and within the marked crossing....
-
M302.2.5 Unobstructed Transfer (Section-by-Section Analysis)
In the MDE NPRM the Access Board proposed that each transfer side provide unobstructed access to the transfer surface, with an exception to permit temporary obstructions as long as they...
-
M302.2.5 Unobstructed Transfer
Each transfer side complying with M302.2.4 shall provide unobstructed access to transfer surfaces. EXCEPTIONS: 1....
-
5.4.1.1 Transfer Support Location Recommendation for Stretchers
Rationale for the recommendation Patients access stretchers on either of the long sides rather than on its end (short side)....
-
Water Closet Clearance
The 1991 Standards allow the nearest side of a lavatory to be placed 18 inches minimum from the water closet centerline and 36 inches minimum from the side wall adjacent to the water closet...
-
Location and Size
The side rails are similar in shape to grab bars and are located on each of the long sides of the table....
-
BEA Inc. Magic Switch Hardwired Touchless Sensor Door Opener MS21H (Wave to Open)
The MS21 is a state-of-the-art touchless activation plate that utilizes capacitance technology to detect and trigger activation in automatic doors. The low profile, hands-free MS21...
-
308.3.2 Obstructed High Reach
The high side reach shall be 48 inches (1220 mm) maximum for a reach depth of 10 inches (255 mm) maximum....
-
308.3.2 Obstructed High Reach
The high side reach shall be 48 inches (1220 mm) maximum for a reach depth of 10 inches (255 mm) maximum....
-
11B-406.5.1 Location
Curb ramps and the flared sides of curb ramps shall be located so that they do not project into vehicular traffic lanes, parking spaces, or parking access aisles....
-
11B-406.5.1 Location
Curb ramps and the flared sides of curb ramps shall be located so that they do not project into vehicular traffic lanes, parking spaces, or parking access aisles....
