Section 221.2.3.2 covers scoping requirements in the current ADA Standards for vertical dispersion in assembly areas.
Search Results "Built-In Element"
-
Vertical Dispersion: ADA Standard Section 221.2.3.2
-
Lawn Seating: ADA Standard Section 221.5
Section 221.5 covers scoping requirements in the current ADA Standards for lawn seating in assembly areas.
-
General Seating: ADA Standard Section 221.2.1.1
Section 221.2.1.1 covers scoping requirements in the current ADA Standards for general seating in assembly areas.
-
Horizontal Dispersion: ADA Standard Section 221.2.3.1
Section 221.2.3.1 covers scoping requirements in the current ADA Standards for horizontal Dispersion in assembly areas.
-
Companion Seats: ADA Standard Section 221.3
Section 221.3 covers scoping requirements in the current ADA Standards for companion seats in assembly areas.
-
Pilot Rock End Accessible Multi-Pedestal Table APT Series
FINISH: Standard finish: hot dip galvanized after fabrication for maximum protection from elements. ...
-
Pilot Rock PQT3-4 Square Pedestal Table Using Lumber
FINISH: Standard finish: hot dip galvanized after fabrication for maximum protection from elements. ...
-
Pilot Rock PQT3-4 Square Pedestal Table Using Recycled Plastic
FINISH: Standard finish: hot dip galvanized after fabrication for maximum protection from elements. ...
-
Oasis Mirage - Dual Option Cooler
300 Series stainless steel tank and external copper refrigerant coil encased in molded foam insulation Hot Water Reservoir with 33.8 ounce, 300 Series stainless steel tank and 450 watt element...
-
Clarity XLC3.4 DECT 6.0 Extra Loud Big Button Speakerphone with Talking Caller ID and ClarityLogic™
The XLC3.4 now gives you our patented ClarityLogic™ customer support service built-in for easy setup and customization of your phone. ...
-
Clarity XLC2 Amplified Cordless Phone
The XLC2 now gives you our patented ClarityLogic™ customer support service built-in for easy setup and customization of your phone....
-
Brinks Home Security Alwood Keyed Entry Lever
Despite being so easy to use, these locks are built to achieve the most rigorous residential security standards as you would expect from Brinks....
-
The Americans with Disabilities Act of 1990
The Americans with Disabilities Act of 1990 The ADA is built upon the foundation laid by Section 504 of the Rehabilitation Act....
-
5.4.6 Transfer Support Gripping Surface Cross Section and Clearances for M301, M302, and M305.2
Rationale for the recommendation The cross section dimensions contained in the 2010 Standards used for grab bars found in the built environment are those contemplated for use in MDE....
-
Tread Obstacles on Outdoor Recreation Access Routes
Where the surface is paved or is built with boards, obstacles must not be more than ½ inch (13 millimeters) high....
-
4.3.5.1 90-Degree Turn
These data are based on measurements of wheeled mobility users performing 90-degree turns in a hallway, built with mock walls. The outside wall of the hallway was fixed....
-
502.5 Vertical Clearance
Every nonresidential structure built on or after January 1, 1991, which is designed to use covered or underground parking as the primary available parking space shall design the covered...
-
Public Rights-of-Way
Some comments asked that the final rule address certain elements common in public rights-of-ways....
-
308.3.2 Obstructed High Reach
Where a clear floor or ground space allows a parallel approach to an element and the high side reach is over an obstruction, the height of the obstruction shall be 34 inches (865 mm) maximum...
-
Associated
Based on the collegiate definition of “associate;” these elements are closely related or connected to the function and use of the water closet....
-
Size and Spacing of Grab Bars and Handrails [4.26.2]
A minimum 18 inch vertical clearance (specified for recessed handrails) may place elements above maximum reach heights....
-
Technical Infeasibility
removing or altering a load-bearing member that is an essential part of the structural frame; or because other existing physical or site constraints prohibit modification or addition of elements...
-
Suggested best practices for architects and other design professionals
In fact, one of the easiest ways to avoid problems is to design construction elements that take the reality of construction tolerances into account....
-
11B-404.2.4.3 Recessed doors and gates
A door can be recessed due to wall thickness or because of the placement of casework and other fixed elements adjacent to the doorway....
