Clearance between support rails and adjacent surfaces shall be 1½ inches (38 mm) minimum....
Search Results "Transfer Support"
Filters
Commonly Searched Documents
-
11B-407.4.10.1 Location
-
11B-407.4.10.1 Location
Clearance between support rails and adjacent surfaces shall be 1½ inches (38 mm) minimum....
-
11B-407.4.10.3 Structural strength
Allowable stresses shall not be exceeded for materials used when a vertical or horizontal force of 250 pounds (1112 N) is applied at any point on the support rail, fastener, mounting device...
-
M305.2.1 Location (Section-by-Section Analysis)
supports so that the support would be reachable during transfer....
-
Clearances Around Gripping Surfaces
The Access Board is considering whether 1½ inches minimum clearance around the gripping surface would be appropriate for transfer supports on diagnostic equipment used by patients in a supine...
-
(5) Bricks and Mortar Transfers
(5) Bricks and Mortar Transfers: A transfer of interest in the Brand Hotel in which, after completion of the transaction, the pre-transfer hotel owner retains management control of hotel...
-
7. Seat Transfer
Are the roll-in showers free of doors that would impede wheelchair transfer onto the seat? [ADA Stds. 4.21.8] Yes __ No __ N/A __ Comments: _______________________________________...
-
Transfer Entry
Transfer Entry There is a large amount of variance in amusement rides and the sides of the ride are often part of the restraint or securement system....
-
Gripping Surface Cross Section and Clearances M301, M302, and M305.2
Gripping Surface Cross Section and Clearances M301, M302, and M305.2 Gripping surface for transfer supports shall be free of sharp or abrasive elements and shall have rounded edges per...
-
(1) Intra-Family Transfers
(1) Intra-Family Transfers: A transfer of interest in a Brand Hotel to or for the benefit of an immediate family member;...
-
Transfer Steps
Transfer Steps The maximum height of transfer steps is 8 inches, although shorter heights are recommended....
-
11B-407.4.10.2 Surfaces
Support rails shall be smooth and any surface adjacent to them shall be free of sharp or abrasive elements....
-
11B-407.4.10.2 Surfaces
Support rails shall be smooth and any surface adjacent to them shall be free of sharp or abrasive elements....
-
11B-407.4.10.2 Surfaces
Support rails shall be smooth and any surface adjacent to them shall be free of sharp or abrasive elements....
-
(2) Transfers Upon Death
(2) Transfers Upon Death: A transfer of interest in a Brand Hotel held by a natural person upon that person's death in accordance with the will or laws of intestacy;...
-
11B-1008.3.2 Transfer steps
Transfer steps shall be provided where movement is intended from transfer platforms to levels with elevated play components required to be on accessible routes....
-
11B-1008.3.2 Transfer steps
Transfer steps shall be provided where movement is intended from transfer platforms to levels with elevated play components required to be on accessible routes....
-
11B-1008.3.2 Transfer steps
Transfer steps shall be provided where movement is intended from transfer platforms to levels with elevated play components required to be on accessible routes....
-
M301.2.3 Transfer Surface Transfer Sides
M301.2.3 Transfer Surface Transfer Sides Subcommittee Recommendation: (Also agreed to by the full committee.)...
-
10. Can a transfer platform be an irregular shape as long as it incorporates the minimum rectangle of 14 by 24 inches?
Can a transfer platform be an irregular shape as long as it incorporates the minimum rectangle of 14 by 24 inches? Yes....
-
Two Step Transfers Attainable Heights
Among the participants that were able to complete the two step transfers, the 5th percentile were able to transfer to a second platform that was 3 inches higher than the first platform for...
-
Head and Back Support (M301.3.3 and M302.3.3)
This is consistent with ANSI/AAMI HE75 which recommends that the “support surface needs to be adjustable or have adjustable support features (e.g., for the head, neck, back, lumbar region...
-
TRANSFER STALLS
[See subsections ...]
-
M305.2.3 Fittings
M305.2.3 Fittings Proposed requirement: Transfer supports shall not rotate within their fittings • Sub-Committee Recommendation: Transfer supports shall not rotate within their...