Transfer Surface Size – M301.2.2 Supine, Prone, or Side-Lying Position The issues were discussed and decided in the full committee meeting as follows: depth of 17 inches minimum and width...
Search Results "Non-Positive Shut Off"
-
Transfer Surface Size – M301.2.2 Supine, Prone, or Side-Lying Position
-
M301.2.3 Transfer Sides
This places the position at a desirable location along the length of the stretcher side so as when the transfer is completed, the patient is in the correct location relative to the articulation...
-
11B-703.8.10 Finish
The background of low resolution VMS characters shall have a non-glare finish....
-
(1) Transfer Surface Location for Diagnostic Equipment Used in the Supine, Prone, or Side-lying Position
Advisory Committee during its deliberations revealed that it is not always possible to transfer from adjoining sides at the end of the diagnostic equipment in the prone, supine, or side-lying position...
-
M301.2.1 Transfer Surface Height
The limitations with these types of tables are that they are typically designed to accommodate >400 lb patients while performing sub-millimeter diagnostic positioning....
-
M305.2.2 Length (Section-by-Section Analysis)
The Access Board specifically sought public input with question 19, asking if the proposed length of the transfer supports would be sufficient to facilitate transfer and maintain position...
-
11B-703.8.10 Finish
The background of low resolution VMS characters shall have a non-glare finish....
-
11B-703.8.10 Finish
The background of low resolution VMS characters shall have a non-glare finish....
-
§8.21(a) New construction
New non-housing facilities shall be designed and constructed to be readily accessible to and usable by individuals with handicaps....
-
11B-407.4.8.2.1 Signal type
Exception: For elevators that have a rated speed of 200 feet per minute (1 m/s) or less, a non-verbal audible signal with a frequency of 1500 Hz maximum which sounds as the car passes or...
-
11B-407.4.8.2.1 Signal type
Exception: For elevators that have a rated speed of 200 feet per minute (1 m/s) or less, a non-verbal audible signal with a frequency of 1500 Hz maximum which sounds as the car passes or...
-
Floor Arrival: ADA Standard Section 407.4.8.1.3
Section 407.4.8.1.3 covers the current ADA Standards for visible floor arrival indicators.
-
Signal Level: ADA Standard Section 407.4.8.2.2
Section 407.4.8.2.2: covers the current ADA Standards for the signal level of audible elevator car indicators.
-
11B-407.4.8.1 Visible indicators
Visible indicators shall comply with Section 11B-407.4.8.1.
-
11B-407.4.8.1 Visible indicators
Visible indicators shall comply with Section 11B-407.4.8.1.
-
11B-407.4.8.1.3 Floor arrival
As the car passes a floor and when a car stops at a floor served by the elevator, the corresponding character shall illuminate. Exception: Reserved. [2010 ADA Standards]...
-
11B-407.4.8.2.2 Signal level
The verbal annunciator shall be 10 dB minimum above ambient, but shall not exceed 80 dB, measured at the annunciator.
-
11B-407.4.8.2.2 Signal level
The verbal annunciator shall be 10 dB minimum above ambient, but shall not exceed 80 dB, measured at the annunciator.
-
11B-407.4.8.1.3 Floor arrival
As the car passes a floor and when a car stops at a floor served by the elevator, the corresponding character shall illuminate. Exception: Reserved. [2010 ADA Standards]...
-
Visible Indicators: ADA Standard Section 407.4.8.1
Section 407.4.8.1 covers the current ADA Standards for visible elevator car position indicators.
-
Signal Type: ADA Standard Section 407.4.8.2.1
Section 407.4.8.2.1 covers the current ADA Standards for the signal type of audible elevator car indicators.
-
Transfer Supports Location and Configuration M301.3 and M302.3
The length of the transfer support shall be a minimum of 15 inches long and positioned so that the transfer support overlaps the length of the transfer surface by 80% at a maximum distance...
-
5.2.1.3 Transfer Surface Size for Stretchers
5.2.1.3 Transfer Surface Size for Stretchers. The transfer surface should be 28 inches wide minimum and 17 inches deep minimum located on both long sides of stretchers.
-
5.4.1.1 Transfer Support Location for Stretchers
5.4.1.1 Transfer Support Location for Stretchers. The transfer surface for stretchers should be oriented along the long side of the surface.