Where two grab bars are provided, the clear deck space shall be centered on the clearance between the grab bars....
Search Results "Hinge Side Clearance"
-
11B-1009.4.1 Clear deck space
-
ASME: ADA Standard Section 105.2.2
Section 105.2.2 of the ADA Standards cover references to the American Society of Mechanical Engineers (ASME) standards.
-
410.1 General
Because an accessible route requires an 80 inch (2030 mm) vertical clearance, care should be taken in selecting lifts as they may not be equally suitable for use by people using wheelchairs...
-
410.1 General
Because an accessible route requires an 80 inch (2030 mm) vertical clearance, care should be taken in selecting lifts as they may not be equally suitable for use by people using wheelchairs...
-
410.1 General
Because an accessible route requires an 80 inch (2030 mm) vertical clearance, care should be taken in selecting lifts as they may not be equally suitable for use by people using wheelchairs...
-
T503 Passenger Access Routes
In the 2016 Non-Rail Vehicle Guidelines, passenger access routes (which were referred to as “accessible circulation paths” in the proposed rule) must provide clearances sufficient to permit...
-
Furnishings and Equipment
In addition, placement of non-fixed elements can affect the accessibility of an area by encroaching into accessible routes and clearances....
-
M303.3.3.4 Edge Protection
Ramps with drop offs ½ inch (13 mm) or greater shall provide edge protection 2 inches (50 mm) high minimum on each side with a drop off....
-
R304.5.1 Width
The clear width of curb ramp runs (excluding any flared sides), blended transitions, and turning spaces shall be 1.2 m (4.0 ft) minimum....
-
407.8.1 Vertical Reference Plane
Operable parts shall be positioned for a side reach or a forward reach determined with respect to a vertical reference plane....
-
5c.
Are the highest floor control buttons in the elevator cab mounted no more than 54 inches above the floor for a side reach or 48 inches for forward reach? Yes _____ No _____...
-
407.12.1 Vertical Reference Plane
Operable parts shall be positioned for a side reach or a forward reach determined with respect to a vertical reference plane....
-
4.30.6 MOUNTING LOCATION AND HEIGHT
Interior signage shall be located alongside the door on the latch side and shall be mounted at a height of between 54 in and 66 in (1370 mm and 1675 mm) above the finished floor....
-
4.34.5.2(1)
The water closet may be located with the clear area at either the right or left side of the toilet....
-
Panda UTS.60 Thermally Broken ULTRA Folding Door System
The top track, bottom track and side profiles form a closed frame. Together with the doors, having aluminum rebates and gaskets, all act in compression....
-
409.4.6.2 Location
Control panels shall be on a side wall, 12 inches (305 mm) minimum from any adjacent wall. Figure 409.4.6.2 Location of Private Residence Elevator Control Panel...
-
T215.2.4 Destination and Route Signs
Where destination or route signs are provided on the exterior of non-rail vehicles, such signs shall be located at a minimum on the front and boarding sides of the vehicle....
-
H23
Is the door to the toilet stall located diagonally opposite, not directly in front of, the toilet or on the opposite side wall from the wall with the long grab bar?...
-
4.7.9 Location at Marked Crossings
Curb ramps at marked crossings shall be wholly contained within the markings, excluding any flared sides (see Fig. 15). ...
-
4.7.9 LOCATION AT MARKED CROSSINGS
Curb ramps at marked crossings shall be wholly contained within the markings, excluding any flared sides (see Fig. 15). Figure 15 Curb Ramps at Marked Crossings...
-
§ 38.159(c)(4) Ramp barriers
Each side of the ramp shall have barriers at least 2 inches (50 mm) high to prevent mobility aid wheels from slipping off....
-
§ 38.95(c)(4) Ramp barriers
Each side of the ramp or bridge plate shall have barriers at least 2 inches high to prevent mobility aid wheels from slipping off....
-
§ 38.125(c)(4) Ramp barriers
Each side of the ramp or bridge plate shall have barriers at least 2 inches high to prevent mobility aid wheels from slipping off....
-
§ 38.83(c)(4) Ramp barriers
Each side of the ramp or bridge plate shall have barriers at least 2 inches high to prevent mobility aid wheels from slipping off....
