A segment of curb at least 24” long beyond flares must be provided on both sides of curb ramps with side flares within marked crossings....
Search Results "Hinge Side Clearance"
-
Diagonal Curb Ramps [§406.6]
-
11B-608.3.2 Standard roll-in type shower compartments
Grab bars shall be provided on the back wall and the side wall opposite the seat. Grab bars shall not be provided above the seat....
-
1009.7.2 Separation
The fire-resistance-rated exterior wall construction shall extend horizontally 10 feet (3048 mm) beyond the landing on either side of the landing or equivalent fire-resistance-rated construction...
-
407.4.1 Car Dimensions
Table 407.4.1 Elevator Car Dimensions Minimum Dimensions Door Location Door Clear Width Inside Car, Side to Side...
-
11B-604 Water closets and toilet compartments
The rear wall grab bar shall be 36 inches (914 mm) long minimum and extend from the centerline of the water closet 12 inches (305 mm) minimum on one side and 24 inches (610 mm) minimum on...
-
Water Hydrants and Water Spouts [1011.2, 1011.3, and 1011.6]
At water hydrants, a minimum of 72 by 48 inches of clear ground space must be provided with the long side of the space adjoining or overlapping an ORAR or trail as applicable, or another...
-
C) Accessible Entrance
If a door is provided, there must be maneuvering space on the pull and push sides of the door to permit a person using a wheelchair to open the door and then move through the door opening...
-
Temporary Solutions for Election Day: Accessible Entrance to Polling Place
Problem Three: Entrance door threshold has an abrupt change in level of more than 1/4 inch and no beveled sides....
-
5. Edge Protection
of the platform, and for double ramped entry platforms, the Committee recommended a minimum two-inch high edge protection on both sides of the platform....
-
11B-610.3 Shower compartment seats
A seat in a standard roll-in shower compartment shall be a folding type, shall be installed on the side wall adjacent to the controls, and shall extend from the back wall to a point within...
-
1133B.2.3.2
greater than 10 and it is determined that compliance with Section 1133B.2.3 would create an unreasonable hardship, a projection of 5/8 inch (16 mm) maximum will be permitted for the latch side...
-
Magnuson Group MECORA Outdoor Waste Receptacle
MECORA secures to the ground and features a locking hinged top for easy removal of waste. Textured steel waste receptacle with one internal compartment and two top openings....
-
1. Standing Supports
preferred side to hold onto the standing support....
-
Standing Supports (M304.3 and M305.3)
M304.3 would require standing supports to be provided on each side of the standing surface on diagnostic equipment used by patients in a standing position....
-
M302.2.3 Size
The size of transfer surfaces shall be measured from center points of their opposing sides....
-
4.16.5* Flush Controls
Controls for flush valves shall be mounted on the wide side of toilet areas no more than 44 in (1120 mm) above the floor....
-
4.16.5* FLUSH CONTROLS
Controls for flush valves shall be mounted on the wide side of toilet areas no more than 44 in (1120 mm) above the floor....
-
4.3.3 Clear Floor Area
The clear floor area width also informs the minimum clearance width for successful passage through corridors, doorways and ramps....
-
General: ADA Standard Section 226.1
Section 226.1 of the ADA Standards covers information in the current ADA Standards on scoping requirements for dining surfaces and work surfaces.
-
602 Drinking Fountains
Substantive changes to this section include: removal of references to water coolers (602.1) requiring all wheelchair accessible drinking fountains to provide knee and toe clearance...
-
Footrests and Armrests
This clearance is needed for people transferring between the lift and a mobility device....
-
Wheelchair Passage Width [4.2.1] and Passing Space [4.2.2]
Additional clearance is needed for maneuvering and sway....
-
AJW Architectural Products U862 Series Dual Toilet Tissue Dispenser & Sanitary Napkin Disposal - Recessed
Hinges: All hinges are full length, heavy duty, stainless steel piano type hinges. Collars: #22 ga stainless steel finished to match cabinet....
-
SDC Z7500 HiTower Pro Series Actuator Controlled Locksets
Hardwire Control with no Electric Hinge and no Wires in the Door....
