ILLUSTRATION 3: Installing a new floor surface in a factory work room is an alteration to a primary function area, but installing a new floor surface in the corridor leading to the work...
Search Results "Ramp Surface"
-
III-6.2000 Alterations: Path of travel
-
11B-809.9.1 Clear floor space
Clear floor spaces 30 inches (762 mm) by 48 inches (1219 mm), with centerlines aligned with the centerline of the work surface, appliance, sink or fixture, shall be provided in the following...
-
Sales and Service Counters, Teller Windows, Information Counters [7.2]
Sales and Service Counters, Teller Windows, Information Counters [7.2] ADAAG generally specifies accessible counter heights up to 34 inches [4.32] but allows a height up to 36...
-
1.1.7 Measurement of parking areas
1.1.7 Measurement of parking areas. Only accessible access aisles and passenger loading zones that are part of a larger parking area need to be measured. These areas should be...
-
M305.3.1 Length (Section-by-Section Analysis)
In the MDE NPRM, the Access Board proposed a gripping surface length of four inches minimum for horizontal standing supports. No public comments were submitted on this requirement....
-
1009.2 Continuity and components
Ramps complying with Section 1012, and Chapter 11A, Sections 1114A and 1122A, or Chapter 11B, 11B-405, as applicable. Areas of refuge complying with Section 1006....
-
M301.2.2 Sunset
The low transfer position height, Item A of M301.2.1, shall cease to have effect on [Insert date 5 years after date of publication in the Federal Register].
-
NYC Board of Elections: Video 6 - Verifying Temporary Solutions
-
AIAU Accessible Architecture: Designing for Success (Parts 1-3)
In Part 2, go in depth on compliance issues regarding accessible routes, ramps, parking spaces, protruding objects, doors and clear floor space, controls, and counters....
-
AquaTrek2 ADA Wading Pool Ramp
AquaTrek2 ADA Wading Pool Ramp The same quality ramp as our Standard AquaTrek2 products, specifically modified to meet the ADA standard for Wading Pool Access....
-
11B-805 Medical care and long-term care facilities
SECTION 11B-805 Medical care and long-term care facilities 11B-805.7 Built-in cabinets and work surfaces....
-
4.1.7(1)(b) Definition
(b) Definition. A qualified historic building or facility is a building or facility that is:
-
M301.2.3 Size (Section-by-Section Analysis)
As discussed in Section IV.B.1.c (Significant Changes – Transfer Surface Size), in the final rule the Access Board has revised this provision to account for the two types of transfer surfaces...
-
11B-1009.4.4 Surface
Surfaces of transfer walls shall not be sharp and shall have rounded edges....
-
11B-1009.5.5 Surface
The surface of the transfer system shall not be sharp and shall have rounded edges....
-
11B-1009.4.4 Surface
Surfaces of transfer walls shall not be sharp and shall have rounded edges....
-
11B-1009.5.5 Surface
The surface of the transfer system shall not be sharp and shall have rounded edges....
-
5.4.5.1 Transfer and Positioning Support Position for Imaging Equipment
The transfer or positioning support should be oriented horizontally on imaging equipment with transfer surfaces....
-
11B-407.4.10.2 Surfaces
Support rails shall be smooth and any surface adjacent to them shall be free of sharp or abrasive elements....
-
11B-407.4.10.2 Surfaces
Support rails shall be smooth and any surface adjacent to them shall be free of sharp or abrasive elements....
-
M301.2.3 Size
The size of the transfer surface shall comply with M301.2.3.1 or M301.2.3.2. The size of transfer surfaces shall be measured from center points of their opposing sides....
-
4.7.9.1 General
Where utility sinks are provided in a recreation facility that also contains a cook top or conventional range, at least 5 percent, but not less than one in each accessible space,...
-
M301.3.1 Transfer Supports
A.1) A transfer support will extend horizontally along the side of the patient scanning/imaging table at least the minimum width of the transfer surface, but in all cases a 28 inches minimum...
