An automatic door may be used as equivalent facilitation when it is technically infeasible to provide sufficient strike-side clearance for code compliance, but a power-assisted door may...
Search Results "Clearance Around Base"
-
11B-404.3 Automatic and power-assisted doors and gates
-
Accessible Restrooms, Fitting Rooms, and Elevators
Remove trash receptacles and cigarette urns from under elevator hall call buttons and beside doors to ensure access to controls and sufficient maneuvering clearance....
-
Rough Grade Site Inspection
surface requirements along accessible routes, accessible parking and access aisles, etc. 11B-403 Verify if under-slab plumbing will provide adequate clearances...
-
Rough Grade Site Inspection
surface requirements along accessible routes, accessible parking and access aisles, etc. 11B-403 Verify if under-slab plumbing will provide adequate clearances...
-
Handrails Along Walking Surfaces [§403.6, §505]
Surface requirements and clearances facilitate a power grip along the length of handrails. Handrails can have circular or non-circular cross-sections, but must have rounded edges....
-
Top Tycoon Free Energy, Spins and Coins Totally New Guide
For me, I've gotten into the habit of checking in during my morning coffee and then again around lunch....
-
I Buy Primal Grow Pro and Here's My Completely Honest Take
No dancing around it. It's marketed primarily toward men who are dealing with concerns around sexual performance, stamina, size, and overall vitality....
-
1017.4.1 Size
The intersection of two trails providing a T-shaped space complying with 304.3.2 where the base and the arms of the T-shaped space extend 48 inches (1220 mm) minimum beyond the intersection...
-
Introduction
Subcommittee members felt that the definitions should be based on how the device is defined by manufacturer as follows: Manufacturers design examination tables with primary functions...
-
§27.127(e)(2)
All decisions are based on the hearing record and written findings shall be made....
-
11B-411.2.1.2.1 Keypads
The dot shall have a base diameter of 0.118 inch (3 mm) minimum and 0.120 inch (3.05 mm) maximum and a height of 0.025 inch (0.6 mm) minimum and 0.037 inch (0.9 mm) maximum....
-
Signage
Recommendations: Signs should include appropriate messages based on the type of system provided, such as "Infrared Assistive Listening System Available -- Please Ask," "Audio Loop in Use...
-
Protruding Objects [4.4]
Requirements in 4.4 are based on standard cane techniques used by people with vision impairments. There are two principal techniques: the touch technique and the diagonal technique....
-
4. I understand that a waiver from accessibility requirements may be obtained?
Such an evaluation is a decision that a business must make based on the cost of barrier removal and the resources of the business, and may require the expert assistance of a CASp, a design...
-
Steps to Minimize Significant Economic Impacts on Small Entities
The final rules permits exceptions to the specific provisions in the technical requirements for certain elements and facilities based on the conditions listed in Table 2 under Executive...
-
1017.4.1 Size
The intersection of two trails providing a T-shaped space complying with 304.3.2 where the base and the arms of the T-shaped space extend 48 inches (1220 mm) minimum beyond the intersection...
-
Testing - Phase I & II
The first set of questions was fact-based and related to their tactile experience and recall of the interpretive information they had been provided at the beginning of the experiment....
-
Must elevator doors remain open for 20 seconds?
The opening time is further determined by the travel distance from hall call buttons and signal timing based on a 1.5 ft/s travel speed beginning from audible and visible signalization of...
-
11B-411.2.1.2.1 Keypads
The dot shall have a base diameter of 0.118 inch (3 mm) minimum and 0.120 inch (3.05 mm) maximum and a height of 0.025 inch (0.6 mm) minimum and 0.037 inch (0.9 mm) maximum....
-
1193.23(b)(4) (Advisory Guidance)
It is important to obtain input from persons or organizations with established expertise to ensure that input is not based merely on individual preferences or limited experience. 2....
-
11B-217.4 TTYs
Separate requirements are provided based on the number of public pay telephones provided at a bank of telephones, within a floor, a building, or on a site....
-
11B-411.2.1.2.1 Keypads
The dot shall have a base diameter of 0.118 inch (3 mm) minimum and 0.120 inch (3.05 mm) maximum and a height of 0.025 inch (0.6 mm) minimum and 0.037 inch (0.9 mm) maximum....
-
11B-217.4 TTYs
Separate requirements are provided based on the number of public pay telephones provided at a bank of telephones, within a floor, a building, or on a site....