PHYSICAL CONSTRUCTION: CONSTRUCTION: Tufted Texture-Twist Loop FACE FIBER: Type 6,6 Four Hole, Hollow Filament Nylon DYE METHOD: Solution / Yarn GAUGE: 1/10 STITCHES PER INCH...
Search Results "Non-public Facing Content"
Filters
Commonly Searched Documents
-
Mannington Mills All Star Collection Commercial Carpet
-
11B-804.2 Clearance
Clearances are measured from the furthest projecting face of all opposing base cabinets, counter tops, appliances, or walls, excluding hardware....
-
608.2.2 Standard Roll-In Type Shower Compartments
mm) wide minimum by 60 inches (1525 mm) deep minimum clear inside dimensions measured at center points of opposing sides and shall have a 60 inches (1525 mm) wide minimum entry on the face...
-
R309.2 Parallel Parking Spaces
Accessible parallel parking spaces located at the end of the block face are usable by vans that have rear lifts and cars that have scooter platforms....
-
3. Measuring Door Openings
Stretch the tape across the door opening to the face of the door....
-
608.2.2.1 Clearance
A 30 inch (760 mm) wide minimum by 60 inch (1525 mm) long minimum clearance shall be provided adjacent to the open face of the shower compartment....
-
4.15.5(1)
Such units shall also have a minimum clear floor space 30 in by 48 in (760 mm by 1220 mm) to allow a person in a wheelchair to approach the unit facing forward....
-
4.13.5 Clear Width
Doorways shall have a minimum clear opening of 32 in (815 mm) with the door open 90 degrees, measured between the face of the door and the opposite stop (see Fig. 24(a), (b), (c), and (d...
-
4.15.5(1)
Such units shall also have a minimum clear floor space 30 in by 48 in (760 mm by 1220 mm) to allow a person in a wheelchair to approach the unit facing forward....
-
Can handrails or other elements overlap door maneuvering clearances?
However, door maneuvering clearances can be offset up to 8” from the face of the door or gate to accommodate wall thickness, casework, shelves, or other elements adjacent to doorways, including...
-
Can handrails overlap door maneuvering clearances?
However, door maneuvering clearances can be offset up to 8” from the face of the door or gate to accommodate wall thickness, casework, shelves, or other elements adjacent to doorways, including...
-
§ 38.29(e)
(e) For vehicles in excess of 22 feet in length with front-door lifts or ramps, vertical stanchions immediately behind the driver shall either terminate at the lower edge of the aisle-facing...
-
11B-804.2 Clearance
Clearances are measured from the furthest projecting face of all opposing base cabinets, counter tops, appliances, or walls, excluding hardware....
-
11B-804.2 Clearance
Clearances are measured from the furthest projecting face of all opposing base cabinets, counter tops, appliances, or walls, excluding hardware. ◼...
-
III. Proposed Accessibility Guidelines
The purpose of this document was to solicit early comment from the public concerning the content of the Accessibility Guidelines, and to outline the Department's procedures for their development...
-
§ 1194.23(b)
(b) Telecommunications products which include voice communication functionality shall support all commonly used cross-manufacturer non-proprietary standard TTY signal protocols....
-
T209.1 General
Where non-rail vehicles provide onboard fare collection devices, at least one fare collection device shall serve a passenger access route and comply with T505....
-
T503.4 Steps at Other Doorways
The walking surface on steps serving all other non-rail vehicle doorways shall be lighted at all times with 2 foot-candles (22 lux) minimum of illumination....
-
Forward Reach [§308.2]
Non-operable portions can be located outside the range....
-
DO-IT Center
Freely distribute online content, publications, and videos for use in presentations, exhibits, and the classroom....
-
Eone Bradley Classic Timepiece Informational Video
Although it serves the same purpose, it is meant for non-visual use by the blind and sighted alike....
-
FAQ: How do I create a new post in Corada Voices?
Required fields are marked with an asterisk (*): Title your post and fill in the Content field, utilizing standard editing tools if needed....
-
C101.1 Purpose
Chapters 3 through 7 (Appendix C), contain scoping and technical requirements for the design, development, and fabrication of telecommunications equipment and customer premises equipment, content...
