Maneuvering clearances for forward approach shall be provided when any obstruction within 18 inches (455 mm) of the latch side of a doorway projects more than 8 inches (205 mm) beyond the...
Search Results "Pull Side"
-
404.2.4.3 Recessed Doors and Gates
-
404.2.4.3 Recessed Doors and Gates
Maneuvering clearances for forward approach shall be provided when any obstruction within 18 inches (455 mm) of the latch side of a doorway projects more than 8 inches (205 mm) beyond the...
-
Medical Diagnostic Equipment Accessibility Standards Sub Committee Recommendations Stretcher Final Report
Specifically, Section M301, Diagnostic Equipment Used by Patients in Supine, Prone, or Side-Lying Position....
-
Innovative Dissertation Writing Services for High-Impact Academic Achievement
Innovative dissertation writing services empower students to achieve high-impact academic success through tailored research support and creative problem-solving approaches. These...
-
Hager Companies Round Pull 10
Round Pull Door Pull Materials: - Aluminum, brass, bronze, stainless steel Certification: - Meets ANSI A156.6 for J401 Pulls...
-
Hager Companies Cast Pull 7N
Cast Door Pull Materials: - Aluminum, Brass, Bronze Options: - May be combined with a plate to make a pull plate Certification: - Meets ANSI A156.6 for J401 Pulls...
-
Hager Companies Cast Pull 5N
Cast Door Pull Materials: - Aluminum, brass, bronze, stainless steel Options: - May be combined with a plate to make a pull plate Certification: - Meets ANSI A156.6 for J401 Pulls...
-
Hager Companies Cast Pull 6N
Cast Door Pull Materials: - Aluminum, brass, bronze, stainless steel Options: - May be combined with a plate to make a pull plate Certification: - Meets ANSI A156.6 for J401 Pulls...
-
Top Landing [§406.4]
Side flares, where provided, are intended primarily to prevent tripping hazards, not to accommodate wheelchair maneuvering at ramps (except in alterations where sufficient landing space...
-
5.6.1 Stirrups for Equipment Used by Patient in Supine, Prone, or Side-Lying Position
5.6.1 Stirrups for Equipment Used by Patient in Supine, Prone, or Side-Lying Position....
-
1132A.5.2 Strike edge maneuvering space at doors
The width of the level area on the side to which the door swings shall extend 18 inches (457 mm) past the strike edge for all doors....
-
Hager Companies Door Pull 974P
Door Pull 974P Pull Material:- Brass, bronze, stainless steel...
-
1132A.5.2 Strike edge maneuvering space at doors
The width of the level area on the side to which the door swings shall extend 18 inches (457 mm) past the strike edge for all doors....
-
11B-404.2.7 Door and gate hardware
Handles, pulls, latches, locks, and other operable parts on doors and gates shall comply with Section 11B-309.4....
-
11B-404.2.7 Door and gate hardware
Handles, pulls, latches, locks, and other operable parts on doors and gates shall comply with Section 11B-309.4....
-
1012.1 General
Parking spaces within camping units and picnic units with mobility features and pull-up spaces for recreational vehicles at dump stations shall comply with 1012....
-
1012.1 General
Parking spaces within camping units and picnic units with mobility features and pull-up spaces for recreational vehicles at dump stations shall comply with 1012....
-
Hager Companies Cast Pull P8N
Cast Door Pull Materials: - Brass Certification: - Meets ANSI A156.6 for J401 Pulls...
-
Lavatory and Accessory Layout by Terry Salo, Architect, CASp
Lavatory and Accessory Layout by Terry Salo, Architect, CASp NOTE: The trash receptacle is preferred to be near the door to allow people to pull the door open with a paper towel...
-
Hager Companies Door Pull 974B
Door Pull Pull Material:- Brass, bronze, stainless steel Base Material:- Black anodized aluminum ...
-
Hager Companies Cast Pull 8N
Cast Door Pull Materials: - Aluminum, Brass, Bronze Certification: - Meets ANSI A156.6 for J401 Pulls...
-
Trimco 1102 Series Cast Pull
Cast from bronze, brass or aluminum, the Trimco 1102 Series Cast Pulls are offered for both thru-bolt (1102T) and surface mount (1102S) applications....
-
1132A.5.2 Strike edge maneuvering space at doors
The width of the level area on the side to which the door swings shall extend 18 inches (457 mm) past the strike edge for all doors....
-
Hager Companies Cast Door Pull 20N
Cast Door Pull Options: - This pull unit may be combined with a plate to make a pull plate Materials: - Brass Certification: - Meets ANSI A156.6 for J401 Pulls...
