5.3.1 Permitted Obstructions to Transfer Sides for Equipment Used by Patients in a Supine, Prone, Side-Lying or Seated Position. A 3-inch maximum obstruction is permitted at transfer...
Search Results "Adjustability"
Commonly Searched Documents
-
5.3.1 Permitted Obstructions to Transfer Sides for Equipment Used by Patients in a Supine, Prone, Side-Lying or Seated Position
-
5.4.3 Transfer Support Height for Equipment Used in a Supine, Prone, Side-Lying, or Seated Position
5.4.3 Transfer Support Height for Equipment Used in a Supine, Prone, Side-Lying, or Seated Position. Transfer supports should be positioned 6 inches minimum and 19 inches maximum...
- Allegion Von Duprin 98/99 Series Von Duprin CVC Traditional and Quick Adjust Bottom Latch Adjustment
-
M305.2.4.2 Non-Circular Cross Section
Transfer supports with non-circular cross sections shall have a cross-section dimension of 2 inches (51 mm) maximum and a perimeter dimension of 4 inches (100 mm) minimum and 4.8...
-
5.4.8 Transfer Support Gripping Surface Hazard Recommendation for M301 and M302
5.4.8 Transfer Support Gripping Surface Hazard Recommendation for M301 and M302 Description: Gripping surface hazards are sharp or abrasive elements that prevent an individual...
-
5.4.8 Transfer Support Gripping Surface Hazard for Equipment Used in a Supine, Prone, Side-Lying, or Seated Position
5.4.8 Transfer Support Gripping Surface Hazard for Equipment Used in a Supine, Prone, Side-Lying, or Seated Position. The gripping surfaces of the transfer support must be free of...
-
Methodology
This study was approved by the University of Pittsburgh's Institutional Review Board and all participants provided informed consent before participating in any test procedures.
-
36 CFR Part 1195 Proposed Accessibility Standards for Medical Diagnostic Equipment NPRM
February 8, 2012 UNITED STATES ACCESS BOARD A FEDERAL AGENCY COMMITTED TO ACCESSIBLE DESIGN 1331 F Street, N.W. Suite 1000 • Washington, D.C. 20004‒1111 (800) 872‒2253...
-
36 CFR Part 1195 Proposed Accessibility Standards for Medical Diagnostic Equipment NPRM - Preamble
February 8, 2012 UNITED STATES ACCESS BOARD A FEDERAL AGENCY COMMITTED TO ACCESSIBLE DESIGN 1331 F Street, N.W. Suite 1000 • Washington, D.C. 20004‒1111 (800) 872‒2253...
-
3.2 Projects with Adjusted Construction Costs Above the Valuation Threshold
3.2 Projects with Adjusted Construction Costs Above the Valuation Threshold: The 20-percent disproportionate cost limitation does not apply to projects with adjusted construction costs above...
-
AN INCREASING NUMBER OF HEALTH CARE PROVIDERS ARE TRANSITIONING TO ADJUSTABLE HEIGHT TABLES
AN INCREASING NUMBER OF HEALTH CARE PROVIDERS ARE TRANSITIONING TO ADJUSTABLE HEIGHT TABLES In 2012, approximately 25 percent of examination tables sold in the U.S. are at about a 19...
- Adjusting the Hager Companies 5100 Door Closer
-
IMPLICATION OF A 19-INCH MINIMUM STANDARD FOR THE HIGHEST POINT IN THE LOWEST ADJUSTABLE POSITION
as the highest point on the transfer surface in a table or chair’s lowest adjustable position....
-
Maneuvering Space, Adjustable Cabinetry, Fixtures and Plumbing
A number of commenters from the disability community stated that it was important that the Guidelines for both kitchens and bathrooms specify a five-foot turning radius; adjustable cabinetry...
-
§104.44 Academic adjustments.
[45 FR 30936, May 9, 1980, as amended at 65 FR 68055, Nov. 13, 2000]
-
§8.33 Housing adjustments.
A recipient shall modify its housing policies and practices to ensure that these policies and practices do not discriminate, on the basis of handicap, against a qualified individual...
-
California Department of Managed Health Care - Physical Access to Health Care Fact Sheet
If You Use a Wheelchair or Have a Hard Time Walking
- Defining and Delivering Disability-Competent Care - The Lived Experience Of Disability
-
M305 Supports
[See subsections ...]
-
M305 Supports (Section-by-Section Analysis)
M305 in the final rule provides the technical requirements for transfer supports, standing supports, leg supports, and head and back supports. Transfer supports are required for...
-
M305 Supports
[See subsections ...]
- Bradley Adjustable Tilt Mirror 782
-
M305.1 General
Supports shall comply with M305.
-
M305.1 General (Section-by-Section Analysis)
This is an introductory section.