Requires the Premium User plan or above.
(Login or upgrade your account!)
Search Results "Surface Slope"
Filters
Commonly Searched Documents
-
Bradley Surface Mounted Stainless Steel Toilet Tissue Dispenser 5402 Plan
-
American Specialties Surface Mounted Roll Paper Towel Holder Model 8165
Requires the Premium User plan or above. (Login or upgrade your account!) -
American Specialties Surface Mounted Seat Cover Dispenser Model 0477-SM
Requires the Premium User plan or above. (Login or upgrade your account!) -
Whitehall Mfg. WH2142T2 Ligature Resistant Toilet Top Supply On-Floor Wall Waste
The toilet is fabricated with 16 gage 304 stainless steel with exterior surfaces powder coated white (interior of toilet will have a satin finish and will not be powder coated). ...
-
Preliminary Guidelines for SEWF Installation
Apply a moderate downward pressure onto the surface so that the mixture compacts tightly....
-
1131A.1 Changes in level not exceeding ½ inch
When changes in level do occur, they shall be beveled with a slope no greater than 1 unit vertical in 2 units horizontal (50-percent slope)....
-
1131A.1 Changes in level not exceeding ½ inch
When changes in level do occur, they shall be beveled with a slope no greater than 1 unit vertical in 2 units horizontal (50-percent slope)....
-
Can van spaces required for a parking garage be located in a surface lot instead?
No. Accessible parking, including van spaces, required for one parking facility can be located in another parking facility only where it results in substantially equal or greater...
-
11B-803.6 Mirrors
Mirrors shall be installed with the bottom edge of the reflecting surface 20 inches (508 mm) maximum above the finish floor or ground....
-
T402 Ramps and Bridgeplates
The technical requirements for ramps and bridgeplates in the 2016 Non-Rail Vehicle Guidelines include provisions on design load, installation and operation, emergency operation, surfaces...
-
Accessibility - Flatness and Lippage
Concrete paving slabs: Laying pattern .. ..90 degree herringbone ..Stack bond or runningbond Slope in direction of travel All segmental concrete paving products...
-
Maintenance (Trail Terminology)
trails, clearing the trail of encroaching brush or grasses, and removing rock slides Maintaining trail tread, such as filling ruts, reshaping a trail bed, repairing a trail surface...
-
Beveled: ADA Standard Section 303.3
Section 303.3 covers the current ADA Standards for beveled level changes.
-
NAADAC Webinar Series: "ADA: The Next Generation" - Virtual and At-Home Training
This unique and important series of seven webinars brings together some of the country’s most experienced ADA experts and trainers, combining the “official” view with practical...
-
1131A.1 Changes in level not exceeding ½ inch
When changes in level do occur, they shall be beveled with a slope no greater than 1 unit vertical in 2 units horizontal (50-percent slope)....
-
11B-903.4 Back support
Back support shall be 48 inches (1219 mm) long minimum and shall extend from a point 2 inches (51 mm) maximum above the seat surface to a point 18 inches (457 mm) minimum above the seat...
-
11B-705.3 Product Approval
Only approved DSA-AC detectable warning products and directional surfaces shall be installed as provided in the California Code of Regulations (CCR), Title 24, Part 1, Chapter 5, Articles...
-
Rise
The maximum length of a run is determined by the rise (30 inches maximum) and the slope: Max. Rise Slope Max. Length Max. Rise Slope Max....
-
Ramp NOW Alumiramp Modular Ramps
anodized aluminum: handrails and ramp will not chip, flake, or rust heavy duty welded aluminum construction non-combustible bidirectional knurled tread forms a rugged skid resistant surface...
-
11B-809.9.2 Clear width
Kitchens shall have a minimum clear width measured between any cabinet, work surface or the face of any appliance (excluding handles and controls) and the opposing cabinet, work surface,...
-
Wading pools. (Section-by-Section Analysis)
Section 242.3 of the 2004 ADAAG provides that newly constructed or altered wading pools must provide at least one sloped means of entry to the deepest part of the pool. ...
-
11B-411.2.1.3.4 Position
The face of individual elements or group of individual elements that are operated by user input shall slope away from the user at 15 to 25 degrees from the vertical plane. ...
-
1134A.6, Item 5
When a threshold is used, it shall be a maximum of 2 inches (50.8 mm) in height and have a beveled or sloped angle not exceeding 1 unit vertical in 2 units horizontal (26.6 degrees from...
-
Transits and construction lasers
Transits and construction lasers are useful for setting or measuring overall elevation points to determine a total slope....
