If a soil stabilizer was installed as part of the trail surface material, please indicate the product name....
Search Results "End Transfer Surface"
Filters
Commonly Searched Documents
-
17. If a soil stabilizer was installed as part of the trail surface material, please indicate the product name.
-
Taking Measurements
Taking Measurements Sloped Surfaces One way to measure slope is to use a 24-inch level with leveling bubble and a tape measure....
-
ADA Solutions, Inc. Radius Tactile Detectable Warning Surface
The Surface Applied Radius Tactile is used to retrofit over an existing concrete substrate and can be installed in as little as 10 minutes....
-
31. Please indicate the number of the complete replacements of the trail surface that you have already performed
Please indicate the number of the complete replacements of the trail surface that you have already performed (in total, so far):...
-
M301.4.2 Clearance Around Base (Section-by-Section Analysis)
In addition, where the width of the examination surface is less than 26 inches, the clearance depth would be the full width of the examination surface. Id....
-
Introduction
Introduction The proposed guidelines for medical diagnostic equipment recommends a minimum transfer surface 30 in. (760mm) wide and 15 in. (381mm) deep. At the request of the U.S....
-
6.3 Minority Reports
6.3 Minority Reports Because the Advisory Committee did not achieve consensus on the recommendation for a minimum transfer surface height standard, U.S....
-
8.4 Improving Data Sources and Research
For example, the Committee was making recommendations about standards for transfer surfaces of certain sizes....
-
T402.7 Edge Guards
Ramps and bridgeplates shall provide edge guards continuously along each side of the ramp or bridgeplate to within 3 inches (75 mm) of the end of the ramp or bridgeplate that is deployed...
-
ADA Solutions, Inc. Cast in Place Tactile Surface
concrete Cast-In-Place Tiles have a 1/4" nominal thickness and feature embedment ribs 3" on center through entire length of tile Plastic sheeting protection covers entire surface...
-
References
References Axelson PW, Chesney D (April 1999): “Accessible Exterior Surfaces Technical Report,” USATBCB, Washington, DC....
-
Gamco Surface Mounted Hand Dryer - DR-5128
Description Surface-mounted ADA (American Disabilities Act) compliant dryer, with stainless steel with brushed finish....
-
11B-407.4.10.1 Location
Clearance between support rails and adjacent surfaces shall be 1½ inches (38 mm) minimum....
-
11B-407.4.10.1 Location
Clearance between support rails and adjacent surfaces shall be 1½ inches (38 mm) minimum....
-
11B-407.4.10.1 Location
Clearance between support rails and adjacent surfaces shall be 1½ inches (38 mm) minimum....
-
1134A.5 Bathtubs
floor space 48 inches parallel by 30 inches perpendicular (1219 mm by 762 mm) to the side of a bathtub or bathtub-shower combination to provide for the maneuvering of a wheelchair and transfer...
-
Benches [1011.2]
However, armrests on both ends of a bench could prevent a person using a mobility device from being able to transfer from the device onto the bench....
-
Gamco Surface-Mounted Robe Hook Satin - 76717
Description (Formerly model 5153) Surface-mounted robe hook shall be type-304 stainless steel with satin-finish....
-
Executive Summary
Performing the task of transferring oneself from one surface to another is highly essential for wheeled mobility device users in order to accomplish everyday activities such as going to...
-
Bobrick Surface-Mounted Sharp Disposal B-350169
Door — 22 gauge stainless steel with exposed surfaces in #4 satin finish. Heavy-duty stainless steel piano-hinge. Tumbler lock keyed like other Bobrick accessories....
-
11B-502.6.3 Location
Signs shall be permanently posted either immediately adjacent to the parking space or within the projected parking space width at the head end of the parking space....
-
28. Have you performed any routine maintenance, repair or replacement of the surface since installation
Have you performed any routine maintenance, repair or replacement of the surface since installation? Yes No If “No” is selected, then skip to “Question #32” (Qualtrics Option)....
-
11B-903.4 Back support
surface....
-
11B-903.4 Back support
surface....
