Where possible, designers are encouraged to locate the transfer device seat no higher than 17 to 19 inches (430 to 485 mm) above the load and unload surface....
Search Results "Loose Fill Surface"
Commonly Searched Documents
-
11B-1002.6 Transfer devices for use with amusement rides
-
5.3.2.3 Slope
The slope of the turning space and clear floor or ground space surface shall not be steeper than 1:48 (2 percent) in all directions....
-
Clearance
Section 403.5 specifies a continuous clearance of 36 inches minimum for walking surfaces....
-
M307.2 Tactilely Discernible (Section-by-Section Analysis)
Patients who are blind or have low vision have difficulty distinguishing a flat membrane button or similar control unless it is tactilely discernible from the surrounding surface and any...
-
R208.1 Where Required
Detectable warning surfaces complying with R305 shall be provided at the following locations on pedestrian access routes and at transit stops: 1....
-
Appendix D: Photometric Measurements
that would be reflected from a perfectly diffusely reflecting surface....
-
Finish and Contrast: ADA Standard Section 703.6.2
Additional factors affecting the ease with which the text can be distinguished from its background include shadows cast by lighting sources, surface glare, and the uniformity of the text...
-
Passing Spaces: ADA Standard Section 403.5.3
Section 403.5.3 covers the current ADA Standards for passing spaces that are part of an accessible route.
-
11B-703.7.2.7 Pedestrian traffic-control buttons
Control buttons shall be located no higher than 48 inches (1219 mm) above the ground surface adjacent to the pole....
-
Polypavement
After uncharacteristically heavy rainfall, the surface became the same texture as mud. Upon drying up, the surface remained cracked and was heaving along the full width of the trail....
- Willoughby Industries WWF-4206 Six Station Full Round 42" Stainless Steel Deep Bowl Washfountain
- Willoughby Industries WWF-3603 Three Station Half Round 36" Stainless Steel Deep Bowl Washfountain
- Willoughby Industries WWF-3606 Six Station Full Round 36" Stainless Steel Deep Bowl Washfountain
-
904.3.2 Counter
The counter surface height shall be 38 inches (965 mm) maximum above the finish floor or ground....
-
4.34.6.4(1)
(1) The counter shall be mounted at a maximum height of 34 in (865 mm) above the floor, measured from the floor to the top of the counter surface, or shall be adjustable or replaceable as...
-
The invisibility of people with disabilities
Will you need any assistance with (getting on and off a table, walking, seeing, reading, hearing, filling out forms, communicating, speaking, during your appointment?...
-
Section 36.309 Examinations and Courses (Section-by-Section Analysis)
Section 309 of the ADA is intended to fill the gap that is created when licensing, certification, and other testing authorities are not covered by section 504 or title II of the ADA, and...
-
19. Q: Does the ADA require all police stations to be accessible to people with disabilities?
It decides to alter the lobby and restrooms so that the areas the public uses -- for filling out crime reports, obtaining copies of investigative reports for insurance purposes, or seeking...
-
ACCESS
If your carrier has an internal procedure for documenting complaints that requires CRO involvement or for documenting other types of passenger complaints, fill out the appropriate forms,...
-
The Inspection Team
In determining who will accompany your team, you should determine what gaps your group may have and fill them with expertise in state and federal access codes, Title III of the ADA,(link...
-
1132A.4 Level floor or landing
Primary entry doors, required exit doors or secondary exterior doors with changes in height between the interior surface or floor level and the exterior surface or floor level shall comply...
-
Seat Height
Commenters noted that this specification should be clarified as applying to the height as measured at the top of the seat surface. Response....
-
11B-904.3.2 Counter
The counter surface height shall be 38 inches (965 mm) maximum above the finish floor or ground....
-
R405.3.3 Minimum Required Depth
Where knee clearance is required under an element as part of a clear space, the knee clearance shall be 280 mm (11 in) deep minimum at 230 mm (9 in) above the finish surface, and 205 mm...