It should be noted that even though manual WC users had higher vibrations for all engineered surfaces, on average they rated all surfaces better than power chair users....
Search Results "Loose Fill Surface"
Filters
Commonly Searched Documents
-
Manual vs. Power (Questionnaire Data)
-
Do basements count in determining a facility’s story count?
As defined in the Standards, a “story” pertains to those portions of buildings “designed for human occupancy included between the upper surface of a floor and upper surface of the floor...
-
DETECTABLE WARNING
A standardized surface feature built in or applied to walking surfaces or other elements to warn of hazards on a circulation path. Advisory Definition of DETECTABLE WARNING....
-
COMPARISON OF OBJECTIVE MEASURES AND ENERGY COSTS
COMPARISON OF OBJECTIVE MEASURES AND ENERGY COSTS Objective measures of surface firmness and stability were compared to energy costs (energy consumption, velocity, RPE and level of difficulty...
-
11B-809.9.2 Clear width
Kitchens shall have a minimum clear width measured between any cabinet, work surface or the face of any appliance (excluding handles and controls) and the opposing cabinet, work surface,...
-
¾ Inch Minus Limestone
After the same two days of uncharacteristically heavy rainfall (as noted in the ¼ inch minus segment), the surface had evidence of water pooling on the surface, as there were lines of pine...
-
11B-903.4 Back support
Back support shall be 48 inches (1219 mm) long minimum and shall extend from a point 2 inches (51 mm) maximum above the seat surface to a point 18 inches (457 mm) minimum above the seat...
-
DETECTABLE WARNING
A standardized surface feature built in or applied to walking surfaces or other elements to warn of hazards on a circulation path. Advisory Definition of DETECTABLE WARNING. ...
-
Water Play Components
If the surface of the accessible route, clear floor or ground spaces, and turning spaces that connect play components are submerged, the accessible route does not have to comply with the...
-
4.34.6.5(1)
(1) The sink and surrounding counter shall be mounted at a maximum height of 34 in (865 mm) above the floor, measured from the floor to the top of the counter surface, or shall be adjustable...
-
11B-705.3 Product Approval
Only approved DSA-AC detectable warning products and directional surfaces shall be installed as provided in the California Code of Regulations (CCR), Title 24, Part 1, Chapter 5, Articles...
-
11B-407.4.10 Support rail
Support rails in elevator cabs are used in a different way than handrails along a walking surface such as a ramp or stairway....
-
DETECTABLE WARNING
A standardized surface feature built in or applied to walking surfaces or other elements to warn persons with visual impairments of hazards on a circulation path....
-
Spectrum Industries Inc. Freedom One Sit-to-Stand Lectern
With the push of a button, a whisper quiet electrical lift adjusts the height of the entire work surface. ...
-
7. EMERGENCY COMMUNICATIONS
Fill in potential strategies and point people to carry out emergency communications during an emergency. DID YOU KNOW?...
-
I. Purpose of the Regulatory Action
This final rule will fill in the gap....
-
Exceptions When Conditions Do Not Permit Full Compliance
negotiation committee report used the example of constructing a portion of a trail in a steeply sloped area, where complying with the provision for running slope would require extensive cuts and fills...
-
FAQ: How do I reply to a post in Corada Voices?
Required fields are marked with an asterisk (*): Title your post and fill in the Content field, utilizing standard editing tools if needed....
-
11B-404.2.7 Door and gate hardware
Door hardware that can be operated with a closed fist or a loose grip accommodates the greatest range of users....
-
11B-404.2.7 Door and gate hardware
Door hardware that can be operated with a closed fist or a loose grip accommodates the greatest range of users....
-
801.1 Scope
For example, 806 addresses guest rooms in transient lodging facilities while 902 contains the technical specifications for dining surfaces....
-
801.1 Scope
For example, 806 addresses guest rooms in transient lodging facilities while 902 contains the technical specifications for dining surfaces....
-
M301.4.2 Clearance Around Base
The base of the equipment shall provide a clearance 6 inches (150 mm) high minimum measured from the floor and 36 inches (915 mm) deep minimum measured from the edge of the examination surface...
-
903.4 Back Support
Back support shall be 42 inches (1065 mm) long minimum and shall extend from a point 2 inches (51 mm) maximum above the seat surface to a point 18 inches (455 mm) minimum above the seat...
