These special hinges are designed to swing the door clear of the opening, adding about 2" additional clearance for wheelchairs and walkers....
Search Results "Grab Bar Clearance"
-
Inclusion Solutions Offset Door Hinge
-
III-7.8200 Restaurants and cafeterias
ADAAG contains requirements for counters and bars, access aisles, food service lines, tableware and condiment areas, raised speaker's platforms, and vending machine areas (but not controls...
-
Paperwork Reduction Act
This rule does not contain any paperwork or record keeping requirements, and does not require clearance under the PRA....
-
11B-604.8.1.1.1 Maneuvering space with in-swinging door
In a wheelchair accessible compartment with an in-swinging door, a minimum 60 inches (1524 mm) wide by 36 inches (914 mm) deep maneuvering space shall be provided in front of the clearance...
-
Paperwork Reduction Act
This rule does not contain any paperwork or record keeping requirements and does not require clearance under the PRA....
-
11B-604.8.1.1.1 Maneuvering space with in-swinging door
In a wheelchair accessible compartment with an in-swinging door, a minimum 60 inches (1524 mm) wide by 36 inches (914 mm) deep maneuvering space shall be provided in front of the clearance...
-
M301.4 Lift Compatibility
An overhead lift (and possibly a gurney-based transfer) may be used in lieu of the provisions for clearances in or around the base of equipment to accommodate the legs of portable floor...
-
Lavatories and Mirrors [4.19]
In those few toilet or bathrooms permitted to be adaptable, base cabinetry is allowed as long as required clear floor space and knee and toe clearances are available when the cabinet is...
-
Don-Jo Mfg., Inc. Pull Plate CFC7015
Number CFC7015 Dimensions 3-1/2" x 15" Ctc 6" Diameter 3/4" Projection 2-1/4" Clearance 1-...
-
11B-604.8.1.2 Doors
Doors shall not swing into the clear floor space or clearance required for any fixture....
-
11B-404.3 Automatic and power-assisted doors and gates
An automatic door may be used as equivalent facilitation when it is technically infeasible to provide sufficient strike-side clearance for code compliance, but a power-assisted door may...
-
11B-404.3 Automatic and power-assisted doors and gates
An automatic door may be used as equivalent facilitation when it is technically infeasible to provide sufficient strike-side clearance for code compliance, but a power-assisted door may...
-
Measuring Door Openings
Door handles and push bars should not be included in the measurements of door opening widths....
-
Table of Contents
CHAPTER 3: BUILDING BLOCKS 301 General 302 Floor or Ground Surfaces 303 Changes in Level 304 Turning Space 305 Clear Floor or Ground Space 306 Knee and Toe Clearance...
-
Forward Approach
Toe/knee clearance below the unit makes this reach easier by allowing a closer approach....
-
Notes:
Otherwise,, it is quite possible to configure a piece of equipment that meets all the clearances yet does not provide accessibility if there is not a defined method of measuring the clearances...
-
11B-604.8.2.2 Doors
Toilet compartment doors, including door hardware, shall comply with Section 11B-404, except that if the approach is to the latch side of the compartment door, clearance between the door...
-
11B-604.8.2.2 Doors
Toilet compartment doors, including door hardware, shall comply with Section 11B-404, except that if the approach is to the latch side of the compartment door, clearance between the door...
-
R306.2 Pedestrian Signal Phase Timing
All pedestrian signal phase timing shall comply with section 4E.06 of the MUTCD (incorporated by reference, see R104.2) and shall be based on a pedestrian clearance time that is calculated...
-
Bobrick ClassicSeries Surface Mounted Seat-Cover Dispenser B-221
Allow 5" (125mm) minimum clearance from bottom of dispenser to top of any horizontal projection for filling dispenser from below unit....
-
902.1 General
Dining surfaces include, but are not limited to, bars, tables, lunch counters, and booths....
-
902.1 General
Dining surfaces include, but are not limited to, bars, tables, lunch counters, and booths....
-
1133B.2.5.2
Latching and locking doors that are hand-activated and which are in a path of travel shall be operable by lever-type hardware, panic bars, push-pull activating bars, U-shaped handles or...
-
Aluminum Heavy Duty Wheels n' Heels® Metro Grating
In addition, the filler bars and main bearing bars are both the same thickness thus providing increased percent open area....
