The top of the fixture rim is a maximum height of 2'10" above the finished floor. If kneespace is provided below the vanity, the bottom of the apron is at least 2'3" above the floor....
Search Results "Floor Surface"
Filters
Commonly Searched Documents
-
7(2)(b)(v)
-
11B-233.3.1.2.6 Public housing facility site impracticality
The site impracticality tests in this section may be used to determine the number of required residential dwelling units with adaptable features in buildings without an elevator,...
-
5.4.2.1 Transfer Support Length for Stretchers
5.4.2.1 Transfer Support Length for Stretchers. Transfer supports on stretchers should be a minimum of 15 inches long.
-
Visual Detection of Detectable Warning Materials by Pedestrians with Visual Impairments - Final Report
(Task Order 18 under Project DTFH61-01-C-00049) Authors: James Jenness & Jeremiah Singer May 24, 2006 Prepared for: Federal Highway Administration Washington,...
-
Accessible Parking Space
Accessible Parking Space
-
11B-407.4.8.1.3 Floor arrival
As the car passes a floor and when a car stops at a floor served by the elevator, the corresponding character shall illuminate. Exception: Reserved....
-
M301.3.1 Transfer Supports (Section-by-Section Analysis)
The only change in the final rule was to update the cross reference to applicable transfer surfaces to accommodate the changes made to transfer surfaces, described above in Section IV.B.1...
-
Rough Form and Foundation Inspection
ensure correct accessible slopes (5% running slope and 2.08% cross slope). 11B-403 Verify forms for sidewalks, ramps, landings, curb ramps and clear floor...
-
Rough Form and Foundation Inspection
ensure correct accessible slopes (5% running slope and 2.08% cross slope). 11B-403 Verify forms for sidewalks, ramps, landings, curb ramps and clear floor...
-
Access Board: Toilet Rooms
This video is part of a longer animation produced by the U.S. Access Board. View the animation video in its entirety on the Access Board's website...
-
M301.2.2 Size
The transfer surface shall be 30 inches (760 mm) wide minimum and 15 inches (381mm) deep minimum. Advisory M301.2.2 Size....
-
Surface
Surface The surface of the transfer platform and steps must not be sharp and must have rounded edges to prevent injuries....
-
7(2)(b)(iv)
The other (non-grab bar) side of the toilet fixture is a minimum of 1'3" from the finished surface of adjoining walls, vanities or from the edge of a lavatory. (See Figure 7(a).)...
-
Magnuson Group UMEA Waste Receptacles
Constructed of painted steel and suitable for both indoors and outdoors, UMEA models can be 1, 2 or 3-compartments wide – each with selectable top inserts and corresponding front...
-
Landscape Forms Inc. Select Modular Steel Recycling Units
Extremely versatile, Select is a modular system of steel recycling units created by industrial designer Brian Kane. Engineered and built for outdoor use the well-proportioned...
-
Sloped Surfaces
Measuring the slope of a ramp, parking space, pedestrian route, or other ground or floor surface is important to identify whether the surface is accessible....
-
Figure 1007.3.2 Golf Club Reach Range Area – Drawing from the U.S. Access Board
-
Surface
Surface Since people using transfer walls are in bathing suits, their skin may be in contact with the wall....
-
General description of monetized benefits for water closet clearance in single-user toilet rooms—out-swinging doors (Req. #28)
In order to assess monetized benefits for the requirement covering water closet clearances in single-user toilet rooms with out-swinging doors, a determination needed to be made...
-
General description of monetized benefits for water closet clearance in single-user toilet rooms—out-swinging doors (Req. # 28)
In order to assess monetized benefits for the requirement covering water closet clearances in single-user toilet rooms with out-swinging doors, a determination needed to be made...
-
M301.2.4 Unobstructed Transfer
Each transfer surface shall provide two unobstructed sides for patient transfer. EXCEPTIONS: 1....
-
M301.2.3 Transfer Sides
The transfer surface shall be located to provide options to transfer from a mobility device onto one short side (depth) and one long side (width) of the surface....
