(i) Where the door swings into the bathroom, there is a clear space (approximately, 2' 6" by 4'0") within the room to position a wheelchair or other mobility aid clear of the path of...
Search Results "Floor Surface"
Filters
Commonly Searched Documents
-
7(2)(b)(i)
-
11B-407.2.3.2 Reserved
ETA Editor's Note Imposing additional requirements regarding characters and colors, the preceding CBC requirements pertaining to elevator hoistway signs are more stringent...
-
11B-407.2.3.2 Reserved
ETA Editor's Note Imposing additional requirements regarding characters and colors, the preceding CBC requirements pertaining to elevator hoistway signs are more stringent...
-
TotTurf® Synthetic Grass: Play Spaces
Description Tot Turf Play Spaces is a line of natural looking, soft, attenuating turf surfacing perfect for playgrounds....
-
Magnuson Group RIGA Series Waste Receptacle
Designed by JM Massana and JM Tremoleda, RIGA is a family of waste receptacles offering various size capacities and that includes a combination ash/trash unit as well as a matching...
-
M305.2.1 Location
Transfer supports shall be located within reach of the transfer surface and shall not obstruct transfer onto or off of the surface when in position....
-
Outside Surfaces
Subsets of the subjects also traveled over outdoor surfaces around the area at which they were tested with the accelerometers attached to their chairs and rated those surfaces....
-
11B-233.3.1.2.6 Public housing facility site impracticality
The remaining ground floor residential dwelling units shall comply with the following requirements: 1. Grab bar reinforcement complying with Section 11B-609. 2. ...
-
5.4.9 Interruptions along Transfer Support Gripping Recommendation for M301 and M302
At the point of connection, these features impede the ability to grasp completely around the cross section of the gripping surface....
-
Why are surface characteristics specified?
Why are surface characteristics specified? Over twenty-seven million Americans report some difficulty in walking....
-
M305.2 Transfer Supports
M305.2 Transfer Supports M305.2.2 Transfer Supports Structural Strength Proposed requirement: Transfer supports and their connections shall be capable of resisting vertical...
-
Stairway Handrails Requirements in the ADA Standards (§504)
Stairway Handrails Requirements in the ADA Standards (§504) Protruding Objects The ADA Standards address hazards posed by protruding objects, such as standpipe...
-
Lift-U® Fold-Out Rising Floor Ramp
When the ramp is rotated to the ramp position, the “Rising Floor” is elevated to vehicle floor level and provides a smooth transition from the rising floor to the vehicle floor, eliminating...
-
11B-703.4.1 Height above finish floor or ground
Tactile characters on signs shall be located 48 inches (1219 mm) minimum above the finish floor or ground surface, measured from the baseline of the lowest Braille cells and 60 inches (1524...
-
703.4.1 Height above Finish Floor or Ground
Tactile characters on signs shall be located 48 inches (1220 mm) minimum above the finish floor or ground surface, measured from the baseline of the lowest tactile character and 60 inches...
-
11B-233.3.1.2.6.5 Additional requirements.
1. Grab bar reinforcement complying with Sections 11B-809.10.5.2, 11B-809.10.6.4, or 11B-809.10.7.3. 2. Interior door opening width complying with Section 11B-404.3.1. 3....
-
Engineered Surfaces
The engineered surfaces consisted of a 16ft x 4ft runway with a 4ft x 4ft flat platform on each end....
-
R310.3.4 Surfaces
R310.3.4 Surfaces. Access aisle surfaces shall comply with R302.7....
-
11B-703.4.1 Height above finish floor or ground
Tactile characters on signs shall be located 48 inches (1219 mm) minimum above the finish floor or ground surface, measured from the baseline of the lowest Braille cells and 60 inches (1524...
-
1009.4.4 Surface
1009.4.4 Surface. Surfaces of transfer walls shall not be sharp and shall have rounded edges....
-
1009.5.5 Surface
1009.5.5 Surface. The surface of the transfer system shall not be sharp and shall have rounded edges....
-
11B-703.4.1 Height above finish floor or ground
Tactile characters on signs shall be located 48 inches (1219 mm) minimum above the finish floor or ground surface, measured from the baseline of the lowest Braille cells and 60 inches (1524...
