Rise of a ramp is the amount of vertical distance the inclined or slanted surface ascends or descends....
Search Results "Vertical Clearance"
-
When Ramps Are Required
-
Gangway Slope and Rise Exceptions
For example, where the vertical distance between where the gangway departs the landside connection and the elevation of the pier surface at the lowest water level is 4 feet, the gangway...
-
1002.6 Transfer Devices for Use with Amusement Rides
Where a series of transfers are required to reach the amusement ride seat, each vertical transfer should not exceed 8 inches (205 mm)....
-
Alterations to stairs (Section-by-Section Analysis)
The 1991 Standards only require interior and exterior stairs to be accessible when they provide access to levels that are not connected by an elevator, ramp, or other accessible means of vertical...
-
Part 1. Typical Issues for Voters Who Use Wheelchairs, Scooters or Other Mobility Aids
Ramps with a vertical rise of more than 6 inches must have handrails on both sides....
-
Data acquisition
The vertical z-axis was chosen because it is parallel to the spine and lower legs of the subject, both of which are high-risk areas for negative health outcomes....
-
1.1.17 Stairs
Measure stair riser height as the vertical dimension between tread nosings....
-
Alterations to stairs. (Section-by-Section Analysis)
The 1991 Standards only require interior and exterior stairs to be accessible when they provide access to levels that are not connected by an elevator, ramp, or other accessible means of vertical...
-
11B-1002.6 Transfer devices for use with amusement rides
Where a series of transfers are required to reach the amusement ride seat, each vertical transfer should not exceed 8 inches (205 mm)....
-
11B-206.3 Location
Additionally, accessible vertical interior circulation must be in the same area as stairs and escalators, not isolated in the back of the facility. ...
-
11B-1002.6 Transfer devices for use with amusement rides
Where a series of transfers are required to reach the amusement ride seat, each vertical transfer should not exceed 8 inches (205 mm). ◼...
-
11B-206.3 Location
Additionally, accessible vertical interior circulation must be in the same area as stairs and escalators, not isolated in the back of the facility. ◼...
-
Table 2: Summary of Department of Transportation Survey
±2" (±50 mm) 16 Vertical placement of handrails, controls, signs, etc. 0 6 in. 1.16 in....
-
Fixed position maps and kiosks
While it is normally more convenient and practical to mount these maps on vertical surfaces, as is typical for publicly displayed maps, it is better to place tactile maps on a horizontal...
-
Slopes and Resting Intervals for Outdoor Recreation Access Routes
Slopes are often described as a ratio of vertical distance to horizontal distance, or rise to run....
-
Feature 4 - Routes to the Meeting Space
Therefore, objects that do not provide sufficient head clearance or that are mounted too high and protrude into a route can become hazards because they cannot be detected by people who use...
-
226 and 902 Dining Surfaces and Work Surfaces
Section 902.2 requires the provision of accessible knee and toe clearance....
-
PART 3: ACCESSIBLE EXAMINATION ROOMS
The features that make this possible are: an accessible route to and through the room; an entry door with adequate clear width, maneuvering clearance, and accessible hardware;...
-
Notes
The committee recognizes that future visionaries may be able to “re-vision” new devices to provide greater clearances and smaller base supports....
-
226.1 General
Consider work surfaces that are flexible and permit installation at variable heights and clearances....
-
Temporary Solutions for Election Day - Hallways and Corridors - Voters Who are Blind or Who Have Low Vision
Problem Two: Ceiling or wall-mounted television monitor has less than 80 inches of clearance between the floor and the bottom of the unit....
-
R404 Clear Spaces (Section-by-Section Analysis)
Clear spaces are permitted to include knee and toe clearance and to be positioned for either forward or parallel approach to an element, unless another requirement specifies otherwise....
-
Mounting Height
It is also consistent with the minimum headroom clearance required for protruding objects....
-
Door and Gate Hardware [§404.2.7]
Recommendations: Specify hardware that is usable with a closed fist of loose grip Bars, pulls, and similar hardware should provide sufficient knuckle clearance (1½” minimum...