Clearance between handrail gripping surfaces and adjacent surfaces shall be 1½ inches (38 mm) minimum....
Search Results "Hinge Side Clearance"
Filters
Commonly Searched Documents
-
11B-505.5 Clearance
-
407.12.2 Side Reach (Section-by-Section Analysis)
407.12.2 Side Reach (Section-by-Section Analysis) This section specifies proposed requirements for operable parts providing unobstructed or obstructed side reaches....
-
11B-809.8.3 Door maneuvering clearance.
At the dwelling unit side of the primary entry doors, secondary exterior doors, and required exit doors maneuvering clearances shall be 44 inches (1118 mm) minimum in length measured...
-
Maximum Depth: ADA Standard Section 306.2.2
Section 306.2.2 covers the current ADA Standards for the maximum depth for toe clearance.
-
4.2.6* SIDE REACH
If the clear floor space allows parallel approach by a person in a wheelchair, the maximum high side reach allowed shall be 54 in (1370 mm) and the low side reach shall be no less than 9...
-
305.4 Knee and Toe Clearance
305.4 Knee and Toe Clearance. Unless otherwise specified, clear floor or ground space shall be permitted to include knee and toe clearance complying with 306....
-
11B-404.3.2 Maneuvering clearance
Clearances at power-assisted doors and gates shall comply with Section 11B-404.2.4....
-
4.2.6* Side Reach
If the clear floor space allows parallel approach by a person in a wheelchair, the maximum high side reach allowed shall be 54 in (1370 mm) and the low side reach shall be no less than 9...
-
Maximum Depth: ADA Standard Section 306.3.2
Section 306.3.2 covers the current ADA Standards for the maximum depth for knee clearance.
-
Side Approach
Side Approach Side reach depth is important to consider in the design and location of sinks....
-
Side Approach
Side Approach Where space is provided for a side approach, controls can be mounted at the heights allowed for side reaches....
-
b. Transfer Surface Location
The MDE NPRM proposed the same location and transfer sides of the transfer surface for diagnostic equipment used by patients in the supine, prone, or side-lying position (M301) and diagnostic...
-
Side Entry Openings, and Width and Length of Wheelchair Space
Side Entry Openings, and Width and Length of Wheelchair Space If the wheelchair space can only be entered from the side, the ride must be designed to permit sufficient turning space for...
-
Transfer Sides (M301.2.3 and M302.2.3)
M301.2.3 and M302.2.3 would require the transfer surface to be located so as to provide patients who use mobility devices the option to transfer onto the short side and the long side of...
-
306.2 Toe Clearance
[See subsections ...]
-
306.3 Knee Clearance
[See subsections ...]
-
306.3 Knee Clearance
[See subsections ...]
-
306.2 Toe Clearance
[See subsections ...]
-
604.5.1 Side Wall
604.5.1 Side Wall....
-
Hager Companies Five Knuckle - Full Mortise Swing Clear Hinge 1260
Five Knuckle - Full Mortise Swing Clear Hinge 1260 - Plain Bearing - Standard Weight Description: - ANSI A8123 - For square edge doors - Non-rising removable pin with...
-
Side Approach and Reach
[See subsections ...]
-
305.4 Knee and Toe Clearance
Unless otherwise specified, clear floor or ground space shall be permitted to include knee and toe clearance complying with 306....
-
305.4 Knee and Toe Clearance
Unless otherwise specified, clear floor or ground space shall be permitted to include knee and toe clearance complying with 306....
-
305.4 Knee and Toe Clearance
Unless otherwise specified, clear floor or ground space shall be permitted to include knee and toe clearance complying with 306....
