See section 406.5 curb ramp location....
Search Results "Curb Ramp Top Landing"
Filters
Commonly Searched Documents
-
502.2 Vehicle Spaces
-
11B-804.2.1 Pass through kitchen
counters, appliances or cabinets are on two opposing sides, or where counters, appliances or cabinets are opposite a parallel wall, clearance between all opposing base cabinets, counter tops...
-
804.2 Clearance
Clearances are measured from the furthest projecting face of all opposing base cabinets, counter tops, appliances, or walls, excluding hardware....
-
M301.2.4 Unobstructed Transfer
Obstructions no more than 3 inches (75 mm) deep shall be permitted to extend beyond transfer sides of transfer surfaces provided that such obstructions do not protrude above the tops of...
-
Issue 4: Based on available references, can we develop “viable” design standards and guidelines”?
Top issues in developing design guidance and standards are: Define Intent Define Problem Signage Severe Changes in Lighting Levels Glare...
-
A. Accessible Counters
.: where no direct service is provided) accessible, providing a 27" high knee space, at least 19" deep, with table/counter tops at 28"-34" above the floor and split proportionately between...
-
Customer Premises Equipment (CPE)
Examples of CPE are telephones, routers, switches, residential gateways, set-top boxes, fixed mobile convergence products, home networking adaptors and Internet access gateways which enable...
-
10.3.1(13)
(13) Where it is necessary to cross tracks to reach boarding platforms, the route surface shall be level and flush with the rail top at the outer edge and between rails, except for a maximum...
-
11B-505.5 Clearance
Handrails may be located in a recess if the recess is 3 inches (76 mm) maximum deep and 18 inches (457 mm) minimum clear above the top of the handrail. [2010 ADAS] 505.5 Clearance. ...
-
11B-505.5 Clearance
Handrails may be located in a recess if the recess is 3 inches (76 mm) maximum deep and 18 inches (457 mm) minimum clear above the top of the handrail....
-
Examination Tables
Treatment tables typically have a flat top. Some models have adjustable backrests, but the backrests typically cannot support patients in a sitting position....
-
Door and Signal Timing
Destination-oriented elevators may have call buttons located outside elevator landing areas and have enhanced programming features for the response time of cars....
-
11B-410.6 Doors and gates
Exception: Platform lifts serving two landings maximum and having doors or gates on opposite sides shall be permitted to have self-closing manual doors or gates....
-
11B-410.6 Doors and gates
Exception: Platform lifts serving two landings maximum and having doors or gates on opposite sides shall be permitted to have self-closing manual doors or gates....
-
Utility Sinks
If utility sinks are provided in a recreation facility that also contains a cook top or conventional range, at least 5 percent (but not less than 1) in each accessible room or space must...
-
Scoping [4.1.3(5)]
In new construction, platform lifts can be used instead of ramps or elevators only in providing access to: performing areas in assembly occupancies wheelchair seating locations...
-
804.2.1 Pass Through Kitchen
counters, appliances or cabinets are on two opposing sides, or where counters, appliances or cabinets are opposite a parallel wall, clearance between all opposing base cabinets, counter tops...
-
1134A.8, Item 1
The top of the fixture rim shall be a maximum of 34 inches (864 mm) above the finished floor....
-
M302.2.5 Unobstructed Transfer
Obstructions no more than 3 inches (75 mm) deep shall be permitted to extend beyond transfer sides of transfer surfaces provided that such obstructions do not protrude above the tops of...
-
R305.1.1 Dome Size
The truncated domes shall have a base diameter of 23 mm (0.9 in) minimum and 36 mm (1.4 in) maximum, a top diameter of 50 percent of the base diameter minimum and 65 percent of the base...
-
1134A.8, Item 1
The top of the fixture rim shall be a maximum of 34 inches (864 mm) above the finished floor....
-
General: ADA Standard Section 205.1
Section 205.1 of the ADA Standards covers information on scoping requirements for operable parts in the most current ADA Standards.
-
Appendix B Trails Study Participation Press Release
Appendix B Trails Study Participation Press Release National Center on Accessibility National Trails Surface Study Press Release NCA Seeks Land Managers with Trails to Participate...
-
R305.2 Placement
Where the back of curb edge is tooled to provide a radius, the border dimension should be measured from the end of the radius....