This applies to switchback ramps, ramps with a 90 degree turn, and angled ramps. Recommendation: Ramps and landings should be configured to facilitate maneuvering....
Search Results "Clear Width at Turn"
Filters
Commonly Searched Documents
-
Landings [4.8.4]
-
TownSteel THSP179 Standard Duty Spring Hinge
All hinges to be with adjustable spring tension with nonremovable pins as listed in hardware groupings and shall be provided with the width that will clear trim to allow for maximum degree...
-
GE® 24" Standard Clean Free-Standing Gas Range JGAS02SENSS
Burner - Right Front 9,100 BTU Burner - Right Rear 9,100 BTU Cooktop Burner Grate Material 2 Doubles Heavy Cast Valves (Degree of Turn...
-
Effective Emergency Management: Making Improvements for Communities and People with Disabilities
; PDF (514 pages, 17.74 MB) Publication Date: August 12, 2009 Executive Summary: The challenges faced by people with disabilities in disaster-threat situations have been made clear...
-
Showers
Several commenters requested that the final Guidelines provide dimensions on the appropriate width and height of showers and shower doors....
-
Re: 405 Ramps
A ramp with a direction change requires a 60" x 60" minimum intermediate landing, which isn't just a turning space but also a place for stopping to allow for a turn....
-
11B-502.6.3 Location
Signs shall be permanently posted either immediately adjacent to the parking space or within the projected parking space width at the head end of the parking space....
-
LaCantina Multi-slide Contemporary Clad Sliding Door System
Panel height may determine max panel width such that the glass does not exceed 60sqft. Color Options LaCantina Doors offer a wide range of in-stock, optional and custom colors....
-
Toilet Room Doors
Sections 4.22.2 and 4.22.3 of the 1991 Standards and Section 603.2.3 of the 2010 Standards permit the doors of all toilet or bathing rooms with in-swinging doors to swing into the required turning...
-
Water Hydrants
This clear space must be located with its long side adjoining (and may overlap) an outdoor recreation access route, trail, beach access route, or another clear ground space....
-
Lutron Sivoia QED Kirbé Vertical Motorized Drapery System
Depending on the width of the drapery, brackets can be selected that accept either a roller 64™ or a roller 100 shade drive. Size Tube diameter: 2.56 in....
-
Stanley SB600 Bifolding Door
Panels fold when retracting which allows for about 70% of the door’s package to be free and clear for passage....
-
1010 Shooting Facilities with Firing Positions
This section requires turning space at firing positions required to be accessible....
-
Lift-U® Fold-Out Rising Floor Ramp
Gaps in floor when deployed – minimal Hinge Knuckles between Ramp & Bus structure – eliminated SPECIFICATIONS Clear width at ramp surface – 30 Inches Minimum...
-
LaCantina Aluminum Thermally Controlled Slider System
Kitchen servery pass through Sizing and Configuration The Aluminum Thermally Controlled system is available in any configuration with panels up to 8' wide and 12' tall, panel width...
-
1118B.3
SECTION 1118B - SPACE ALLOWANCE AND REACH RANGES 1118B.3 Wheelchair turning space. ...
-
Guidelines for Requirement 3
(2) For doors within individual dwelling units, the Department has retained, in the final Guidelines, the design specification that a door with a clear opening of at least 32 inches...
-
Elevated Dune Crossings
The clear width of elevated dune crossings may be narrower than the rest of the beach access route, but must be at least 48 inches (1,220 millimeters)....
-
1016.1 General
The technical requirements address the surface of outdoor recreation access routes, passing spaces, and resting intervals (1016.2); the clear width of outdoor recreation access routes (1016.3...
-
802.1.5 Overlap
The term "circulation paths" used in 802.1.5 means aisle width required by applicable building or life safety codes for the specific assembly occupancy....
-
11B-802.1.5 Overlap
The term "circulation paths" used in 802.1.5 means aisle width required by applicable building or life safety codes for the specific assembly occupancy....
-
802.1.5 Overlap
The term "circulation paths" used in 802.1.5 means aisle width required by applicable building or life safety codes for the specific assembly occupancy....
