In most cases, it is best to refer to industry standard tolerances or other industry documents when they exist....
Search Results "Electroacoustic Performance Standards"
-
2.1.1
-
16(a)(vii)
(vii) Any non-valet parking facilities owned or operated by the hotel have the number of accessible car and van-accessible parking spaces required by the ADA Standards and comply with the...
-
§ 35.151(c)(1)
construction or alterations commence after July 26, 1992, but prior to September 15, 2010, then new construction and alterations subject to this section must comply with either UFAS or the 1991 Standards...
-
§ 36.406(c) Places of lodging.
Places of lodging subject to this part shall comply with the provisions of the 2010 Standards applicable to transient lodging, including, but not limited to, the requirements for transient...
-
§35.103(a)
Except as otherwise provided in this part, this part shall not be construed to apply a lesser standard than the standards applied under title V of the Rehabilitation Act of 1973 or the regulations...
-
§ 35.103(a) Rule of interpretation
Except as otherwise provided in this part, this part shall not be construed to apply a lesser standard than the standards applied under title V of the Rehabilitation Act of 1973 or the regulations...
-
11B-604.4 Seats
[2010 ADA Standards] 604.4 Seats....
-
11B-502.5 Vertical clearance
[2010 ADA Standards] 502.5 Vertical Clearance....
-
11B-904.4.1 Parallel approach
[2010 ADA Standards] 904.4.1 Parallel Approach....
-
11B-904.4.1 Parallel approach
[2010 ADA Standards] 904.4.1 Parallel Approach....
-
11B-502.5 Vertical clearance
[2010 ADA Standards] 502.5 Vertical Clearance....
-
11B-604.4 Seats
[2010 ADA Standards] 604.4 Seats....
-
Panda TS.87 Thermally Broken Slim Profile Lift & Slide System
This model features an extra-low U-value, adding greater performance and weather protection to its genuine elegance....
-
Location of Accessible Routes
The 2010 Standards require all accessible routes to coincide with or be located in the same general area as general circulation paths....
-
May an employer have an employee who it reasonably believes will pose a direct threat examined by its own health care provider?
in the employee's specific medical condition and be able to provide medical information that allows the employer to determine the effects of the condition on the employee's ability to perform...
-
3. Does the ADA require an applicant to disclose that she has or had a hearing impairment or some other disability before accepting a job offer?
Sometimes, the decision to disclose depends on whether an individual will need a reasonable accommodation to perform the job (for example, specialized equipment, removal of a marginal function...
-
Why are surface characteristics specified?
The information in this Bulletin was derived from this and other research in order to provide designers with an understanding of the variables that affect the measurement and performance...
-
R201 Application (Section-by-Section Analysis)
., towers and temporary performance stages and reviewing stands)....
-
Miniature Horses
addition to the provisions about service dogs, the Department’s revised ADA regulations have a new, separate provision about miniature horses that have been individually trained to do work or perform...
-
4.20.2 Floor Space
However, because frail older adults do not perform sliding transfers, clear floor space in eldercare facilities was needed for one or more caregivers to be able to assist with getting in...
-
a. Structural Strength
Industry must follow testing parameters found in other standards.”...
-
1. Rationale for Incorporation by Reference
They are as follows: First, our approach is consistent with that taken by other international standards organizations dealing with this issue....
-
Section 1194.21 Software Applications and Operating Systems (Preamble, Section-by-Section Analysis)
For example, most of the menu functions in common drawing programs that allow a user to open, save, size, rotate, and perform other actions on a graphic image can all be performed from the...
-
III-7.5190 Dressing and fitting rooms
Technical standards are provided for doors, benches, and mirrors, with less stringent standards for alterations....
